|
|
Sponsored Content
Operating Systems
Solaris
USB to Serial Adapter connection
Post 302306237 by aixlover on Saturday 11th of April 2009 08:27:20 PM
04-11-2009
|
|
10 More Discussions You Might Find Interesting
1. Linux
I have a serial modem connected to a usb port using an adapter cable. The system is a HP DL360. RedHat ES3.0
I am using the device /dev/ttyUSB0
When I issue the command "mgetty ttyUSB0" I get the following output in the log file.
How do I get the system to see the modem.
12/02 14:17:55... (2 Replies)
Discussion started by: jshoovie
2 Replies
2. UNIX for Dummies Questions & Answers
hi all,
i've got an old PC with unix (SCO System V/386 rel. 3.2) on it.
Pentium I; 128mb; ISA 2-port RS232 serial adapter card for an oki dot-matrix printer. (no usb, no CD)
i've been running an old cobol program to do some invoicing and print reports.
some time back i changed the... (0 Replies)
Discussion started by: frankpky
0 Replies
3. SCO
According to sco6 usb supplement, once you install it, you can install a bafo industries (BF-810) in the computer. I have done all that and followed the intructions completely and it shows up using usbprobe and l /dev/usb_ser*
Problem is that when I go to mkdev serial, it is not there.
Anyone... (1 Reply)
Discussion started by: jn5519
1 Replies
4. Solaris
Hi all,
I must connect my PC (Windows 2000) to Sun Enterprise 450 (4 X UltraSPARC-II 400Mhz) for Solaris 10 Installation. My PC doesn't have a serial port therefore I must use USB port.
How can I connect USB port of my PC to the serial port (DB 25) of Sun 450?
Will be there any problems with... (3 Replies)
Discussion started by: Sunb3
3 Replies
5. UNIX for Dummies Questions & Answers
Hi iam new bie to unix.
we are getting the sensor positional values on hyperterminal(UART).but
our task is to use this data for mouse movement.so wat we hav to do ??
is this required to change usb driver cud u send info regarding my query??
Thanks in advance :) :) :) (1 Reply)
Discussion started by: jayakar
1 Replies
6. IP Networking
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Discussion started by: rsd220
5 Replies
7. Solaris
Hi,
i try to plug in my USB wireless adapter to my sun solaris server. However, it cannot detect it. How do i set it so that it can detect it? (1 Reply)
Discussion started by: lkyow
1 Replies
8. Hardware
Hi Gurus of Unix
Recently I install a OpenSolaris in My HP 530
In this moment want to install a USB-A to Serial Cable. Any guru can send a Link where I can use how reference.
I want to configure a Router and my PC don't have any serial Port.
My LapTOP only has USB ports. In this case I buy a... (2 Replies)
Discussion started by: andresguillen
2 Replies
9. Solaris
In ubuntu etopic i create this udev rules for prolink 3g usb modem:
SUBSYSTEM=="block",
SUBSYSTEM=="scsi",
ATTRS{idVendor}=="1e0e",
ATTRS{idProduct}=="f000",
ACTION=="add",
RUN+="/sbin/modprobe usbserial Vendor=0X1e0e Product=0Xf000"
After plugging the usb modem, ubuntu assigns the ports... (4 Replies)
Discussion started by: shamsat
4 Replies
10. Linux
I have someone wanting to connect to the serial management port of a switch from a PC running CentOS6. The management port on the switch is apparently baud 9600, 8 data bits, 1 stop bit & no parity They have plugged in a cable to connect and the output from lsusb is:-Bus 001 Device 001: ID... (7 Replies)
Discussion started by: rbatte1
7 Replies
LEARN ABOUT NETBSD
ehci
EHCI(4) BSD Kernel Interfaces Manual EHCI(4) NAME
ehci -- USB Enhanced Host Controller driver SYNOPSIS
ehci* at cardbus? function ? ehci* at pci? dev ? function ? usb* at ehci? DESCRIPTION
The ehci driver provides support for the USB Enhanced Host Controller Interface, which is used by USB 2.0 controllers. EHCI controllers are peculiar in that they can only handle the USB 2.0 protocol. This means that they normally have one or more companion controllers (i.e., ohci(4) or uhci(4)) handling USB 1.x devices. Consequently each USB connector is electrically connected to two USB con- trollers. The handling of this is totally automatic, but can be noticed since USB 1.x and USB 2.0 devices plugged in to the same connector appear to connect to different USB busses. SEE ALSO
cardbus(4), ohci(4), pci(4), uhci(4), usb(4) HISTORY
The ehci driver appeared in NetBSD 1.6. BUGS
The support for hubs that are connected with high speed upstream and low or full speed downstream (i.e., for transaction translators) is lim- ited. BSD
Aug 10, 2008 BSD