04-11-2009
Is your problem solved? What type of USB-to-DB9 cable do you use?
10 More Discussions You Might Find Interesting
1. Linux
I have a serial modem connected to a usb port using an adapter cable. The system is a HP DL360. RedHat ES3.0
I am using the device /dev/ttyUSB0
When I issue the command "mgetty ttyUSB0" I get the following output in the log file.
How do I get the system to see the modem.
12/02 14:17:55... (2 Replies)
Discussion started by: jshoovie
2 Replies
2. UNIX for Dummies Questions & Answers
hi all,
i've got an old PC with unix (SCO System V/386 rel. 3.2) on it.
Pentium I; 128mb; ISA 2-port RS232 serial adapter card for an oki dot-matrix printer. (no usb, no CD)
i've been running an old cobol program to do some invoicing and print reports.
some time back i changed the... (0 Replies)
Discussion started by: frankpky
0 Replies
3. SCO
According to sco6 usb supplement, once you install it, you can install a bafo industries (BF-810) in the computer. I have done all that and followed the intructions completely and it shows up using usbprobe and l /dev/usb_ser*
Problem is that when I go to mkdev serial, it is not there.
Anyone... (1 Reply)
Discussion started by: jn5519
1 Replies
4. Solaris
Hi all,
I must connect my PC (Windows 2000) to Sun Enterprise 450 (4 X UltraSPARC-II 400Mhz) for Solaris 10 Installation. My PC doesn't have a serial port therefore I must use USB port.
How can I connect USB port of my PC to the serial port (DB 25) of Sun 450?
Will be there any problems with... (3 Replies)
Discussion started by: Sunb3
3 Replies
5. UNIX for Dummies Questions & Answers
Hi iam new bie to unix.
we are getting the sensor positional values on hyperterminal(UART).but
our task is to use this data for mouse movement.so wat we hav to do ??
is this required to change usb driver cud u send info regarding my query??
Thanks in advance :) :) :) (1 Reply)
Discussion started by: jayakar
1 Replies
6. IP Networking
i have wireless usb adapter rtl8187 from micromax company
my proplem is the signal is very weak and i cannot open website
can i increase the signal ?
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0... (5 Replies)
Discussion started by: rsd220
5 Replies
7. Solaris
Hi,
i try to plug in my USB wireless adapter to my sun solaris server. However, it cannot detect it. How do i set it so that it can detect it? (1 Reply)
Discussion started by: lkyow
1 Replies
8. Hardware
Hi Gurus of Unix
Recently I install a OpenSolaris in My HP 530
In this moment want to install a USB-A to Serial Cable. Any guru can send a Link where I can use how reference.
I want to configure a Router and my PC don't have any serial Port.
My LapTOP only has USB ports. In this case I buy a... (2 Replies)
Discussion started by: andresguillen
2 Replies
9. Solaris
In ubuntu etopic i create this udev rules for prolink 3g usb modem:
SUBSYSTEM=="block",
SUBSYSTEM=="scsi",
ATTRS{idVendor}=="1e0e",
ATTRS{idProduct}=="f000",
ACTION=="add",
RUN+="/sbin/modprobe usbserial Vendor=0X1e0e Product=0Xf000"
After plugging the usb modem, ubuntu assigns the ports... (4 Replies)
Discussion started by: shamsat
4 Replies
10. Linux
I have someone wanting to connect to the serial management port of a switch from a PC running CentOS6. The management port on the switch is apparently baud 9600, 8 data bits, 1 stop bit & no parity They have plugged in a cable to connect and the output from lsusb is:-Bus 001 Device 001: ID... (7 Replies)
Discussion started by: rbatte1
7 Replies
LEARN ABOUT FREEBSD
usb_template
USB_TEMPLATE(4) BSD Kernel Interfaces Manual USB_TEMPLATE(4)
NAME
usb_template -- USB templates
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device usb_template
To load the module at boot time, place the following line in loader.conf(5):
usb_template_load="YES"
DESCRIPTION
The usb_template module implements various USB templates that are needed when programming an USB device side driver. A USB template consists
of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
descriptors, USB strings and additional USB descriptors. The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
ernet and Message Transfer Protocol. USB templates are currently selected using the "hw.usb.template" sysctl. The "hw.usb.template" value
can be changed at any time, but will not have any effect until the USB device has been re-enumerated.
SEE ALSO
usb(4)
STANDARDS
The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.
HISTORY
The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.
BSD
March 18, 2014 BSD