01-05-2009
ethernet down
Thanks for your reply padow
I change the switch port and the ethernet cable but still the same thing.
I forget to say this server has Hacmp. Right now I dont use hacmp and all the services and daemons are down right now. the other server I dont have problem with the net and the same all the services are down.
But I still have the problem with the ip intermittent.
Thanks
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
Discussion started by: at_renai2001
5 Replies
2. UNIX for Dummies Questions & Answers
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies
3. Cybersecurity
I suspect that someone is using a sniffer on my Ethernet connection,
OS X 10.3.9, DSL,
ok, I'm in terminal using the "ifconfig" command >
flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384
right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
Discussion started by: su"do"er
1 Replies
4. UNIX for Advanced & Expert Users
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
7. Solaris
my solris box network is unreachable how to solve this
ipaddress assiagning and entry in vi /etc/host
how to solve network is unreachable (2 Replies)
Discussion started by: tirupathi
2 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
LEARN ABOUT DEBIAN
spd-conf
SPD-CONF(1) General Commands Manual SPD-CONF(1)
NAME
spd-conf - A simple tool for basic configuration of Speech Dispatcher and problem diagnostics
SYNOPSIS
spd-conf [options]
DESCRIPTION
spd-conf is a simple tool for basic configuration of Speech Dispatcher and problem diagnostics
OPTIONS
-h, --help
show this help message and exit
-e, --espeak
Use espeak to synthesize messages
--test-festival
Test whether Festival works as a server
-s, --test-spd-say
Test connection to Speech Dispatcher using spd-say
--test-pulse
Test Pulse Audio
-c, --config-basic-settings-user
Configure basic settings in user configuration
-u, --create-user-conf
Create Speech Dispatcher configuration for the given user
-C, --config-basic-settings-system
Configure basic settings in system-wide configuration
-n, --dont-ask
Do not ask any questions, always use default values
--test-alsa
Test ALSA audio
--test-espeak
Test whether Espeak works as a standalone binary
-d, --diagnostics
Diagnose problems with the current setup
-D, --debug
Debug a problem and generate a report
AUTHOR
spd-conf was written by Hynek Hanke <hanke@brailcom.org>. The webpage for this package can be found at http://www.freebsoft.org/speechd.
This manual page was written by Luke Yelavich <themuso@ubuntu.com>, for the Ubuntu project (but may be used by others).
August 24, 2009 SPD-CONF(1)