01-05-2009
ethernet down
Thanks for your reply padow
I change the switch port and the ethernet cable but still the same thing.
I forget to say this server has Hacmp. Right now I dont use hacmp and all the services and daemons are down right now. the other server I dont have problem with the net and the same all the services are down.
But I still have the problem with the ip intermittent.
Thanks
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
Discussion started by: at_renai2001
5 Replies
2. UNIX for Dummies Questions & Answers
I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by... (1 Reply)
Discussion started by: at_renai2001
1 Replies
3. Cybersecurity
I suspect that someone is using a sniffer on my Ethernet connection,
OS X 10.3.9, DSL,
ok, I'm in terminal using the "ifconfig" command >
flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384
right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the... (1 Reply)
Discussion started by: su"do"er
1 Replies
4. UNIX for Advanced & Expert Users
I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up? (1 Reply)
Discussion started by: capeme
1 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. Solaris
Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args:
SunOS Release 5.8 Version Generic_108528-29 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
ifconfig: plumb: qfe2: Bad file number
configuring IPv4 interfaces: eri0.
moving addresses... (1 Reply)
Discussion started by: fredginting
1 Replies
7. Solaris
my solris box network is unreachable how to solve this
ipaddress assiagning and entry in vi /etc/host
how to solve network is unreachable (2 Replies)
Discussion started by: tirupathi
2 Replies
8. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
9. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
SERVICES(5) BSD File Formats Manual SERVICES(5)
NAME
services -- service name data base
DESCRIPTION
The services file contains information regarding the known services available in the DARPA Internet. For each service a single line should
be present with the following information:
official service name
port number
protocol name
aliases
Items are separated by any number of blanks and/or tab characters. The port number and protocol name are considered a single item; a ``/''
is used to separate the port and protocol (e.g. ``512/tcp''). A ``#'' indicates the beginning of a comment; subsequent characters up to the
end of the line are not interpreted by the routines which search the file.
Service names may contain any printable character other than a field delimiter, newline, or comment character.
INTERACTION WITH DIRECTORY SERVICES
Processes generally find service records using one of the getservent(3) family of functions, or using getaddrinfo(3). On Mac OS X, these
functions interact with the DirectoryService(8) daemon, which reads the /etc/services file as well as searching other directory information
services to determine service name, protocol, and port information.
FILES
/etc/services
SEE ALSO
getservent(3), getaddrinfo(3), DirectoryService(8)
HISTORY
The services file format appeared in 4.2BSD.
4.2 Berkeley Distribution June 5, 1993 4.2 Berkeley Distribution