Problem with Etherchannel Post: 302253362

10 More Discussions You Might Find Interesting

1. AIX

EtherChannel network redundance problem

Problem description: On the condition of EtherChannel function of AIX, when the data exchange between the nodes on the network, there sometimes lost datat packets and cause the application failed. Once we deconfig EtherChannel and use the single adapter configuration, the application works...

2. AIX

AIX / Etherchannel / VLANs

I have 1 AIX server, 4 dual ported fiber attached ethernet cards and 4 VLANS coming in. Is it possible to present those 8 ports as 1 IP address using etherchannel? Thanks.

3. AIX

How to find the active network inteface on etherchannel

I have a server with multiple network interfaces. 2 of these interfaces, lets say en2 and en6 make up an etherchannel interface, which let's say en8. when I run the command lsattr -El ent8 I can see the designated primary and backup interfaces as ent6 and ent2, in the given order. But...

4. BSD

FreeBsd 8.0 : Just for Gurus! Trunk/Etherchannel mode

Hi Buddies! I need to do a new kind of setting in FreeBSD (i'm a newbie using this OS). Interface 1 y 2 in Trunk/Etherchannel mode IP-> xx.xx.xx.xx netmask-> 255.255.255.0 Anybody can help me with a step by step Guide?. THANKS A MILLION!!!

5. AIX

Pb Etherchannel/deconnexion port reseau

Hello, On a partition with AIX 5300-11-01-0944. 1 etherchannel ent9 with aggregation ent3/ent7. # lsdev |grep ent ... ent3 Available 07-01 4-Port 10/100/1000 Base-TX PCI-Express Adapter (14106803) ... ent7 Available 0A-01 4-Port 10/100/1000 Base-TX PCI-Express...

6. AIX

Can EtherChannel be a redundancy config?

I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches. How to make this as a redundancy config? Current is if one physical network adapter down, the seond one will go through the network. but if...

7. AIX

EtherChannel interface ping pelicularity

I have few AIX servers in my data center, which have their EtherChannel configured to have a fat pipe (active/active) and a nagios server to monitor the server uptimes. Nagios server pings every server in the data center and we have pretty much every known unix flavor in this data center. When...

8. AIX

Aggregated Etherchannel

Hi, I have a AIX5.3 P6-520 with 8x1Gb Ethernet ports with possible connections to 2 CISCO 2960 switches. I can create 8023ad Etherchannels which work correctly with the switches (I have set up for LACP passive and a valid channels) But can create 2x 8023ad 4Gb Etherchannels with no backups....

9. AIX

Etherchannel failover testing

Hi Guys, I am trying to test an etherchannel failover and switchback. I did failover from primary to backup adapter, but now I am not able to switch it back to primary. phcxxxxx:/ > entstat -d ent4 | grep Active Active channel: backup adapter ...

10. AIX

PowerVM SEA etherchannel performance ?

Hello, POWER7 machine. 4 x 1Gbit port ethernet adapter is dedicated to vios. 8023ad etherchannel is created using those 4 ports. Etherchannel adapter is shared to lpars using SEA. If I test network performance directly from vios partition (using iperf) I'm geting nice 4Gbit throughput. But if...

LEARN ABOUT NETBSD

bnx

BNX(4)							   BSD Kernel Interfaces Manual 						    BNX(4)

NAME

     bnx -- Broadcom NetXtreme II 10/100/1000 Ethernet device

SYNOPSIS

     bnx* at pci?
     brgphy* at mii?

DESCRIPTION

     The bnx driver supports Broadcom's NetXtreme II product family, such as the BCM5706 PCI-X and BCM5708-BCM5709 PCI Express Ethernet con-
     trollers, which includes the following:

     o	 Dell PowerEdge 1950 integrated BCM5708 NIC (10/100/1000baseT)
     o	 Dell PowerEdge 2950 integrated BCM5708 NIC (10/100/1000baseT)
     o	 Dell PowerEdge M710 integrated BCM5709S NIC (1000baseSX)
     o	 HP NC370F PCI-X Multifunction Gigabit server adapter (1000baseSX)
     o	 HP NC370T PCI-X Multifunction Gigabit server adapter (10/100/1000baseT)
     o	 HP NC373F PCI Express Multifunction Gigabit server adapter (1000baseSX)
     o	 HP NC373i PCI Express Multifunction Gigabit embedded server adapter (10/100/1000baseT)
     o	 HP NC380T PCI Express Dual Port Multifunction Gigabit server adapter (10/100/1000baseT)
     o	 IBM xSeries 3550 integrated BCM5708 NIC (10/100/1000baseT)
     o	 IBM xSeries 3650 integrated BCM5708 NIC (10/100/1000baseT)

     The NetXtreme II product family is composed of various Converged NIC (or CNIC) Ethernet controllers which support a TCP Offload Engine (TOE),
     Remote DMA (RDMA), and iSCSI acceleration, in addition to standard L2 Ethernet traffic, all on the same controller.  The following features
     are supported in the bnx driver under NetBSD:

	   IPv4 receive IP/TCP/UDP checksum offload
	   Jumbo frames (up to 9022 bytes)
	   VLAN tag insertion
	   Interrupt coalescing
	   10/100/1000Mbps operation in full-duplex mode
	   10/100Mbps operation in half-duplex mode

     The bnx driver supports the following media types:

     autoselect   Enable autoselection of the media type and options.  The user can manually override the autoselected mode via ifconfig(8).

     10baseT/UTP  Set 10Mbps operation.  The ifconfig(8) mediaopt option can also be used to select either full-duplex or half-duplex modes.

     100baseTX	  Set 100Mbps (Fast Ethernet) operation.  The ifconfig(8) mediaopt option can also be used to select either full-duplex or
		  half-duplex modes.

     1000baseTX   Set 1000baseTX operation over twisted pair.  Only full-duplex mode is supported.

     1000baseSX   Set 1000Mbps (Gigabit Ethernet) operation.  Both full-duplex and half-duplex modes are supported.

     2500baseSX   Set 2500Mbps operation.  Only full-duplex mode is supported.

     The bnx driver supports the following media options:

     full-duplex  Force full duplex operation.

     half-duplex  Force half duplex operation.

     For more information on configuring this device, see ifconfig(8).

SEE ALSO

     arp(4), brgphy(4), ifmedia(4), intro(4), mii(4), netintro(4), pci(4), ifconfig(8)

HISTORY

     The bnx device driver first appeared in NetBSD 4.0.

BSD
								 December 10, 2010							       BSD