10-23-2008
can know how to run the above command in diff host :
means
i want to run like
ssh -l < host > ifconfig | awk '/^eth/{s=$1;getline;print s,$1,$2}'
but it was not working..
could you please help me in that
10 More Discussions You Might Find Interesting
1. Solaris
hi all
iam trying to set my eri0 interface but with little luck .
when i set the ip using ipconfig i always get "bad adress"..
moreover when i use ifconfig eri0 i can notice that the inet is 0.0.0.0 and the netmask 0
i am runnig solaris 9 on sparc .
any helpis highly appreciated ... ... (2 Replies)
Discussion started by: ppass
2 Replies
2. UNIX for Dummies Questions & Answers
if i have the command ifconfig eth0, what will the output be and how can i use either awk or grep to isolate and display the IP address, subnet mask and physical address of my host (1 Reply)
Discussion started by: carlvernon
1 Replies
3. IP Networking
Hello,
I have a server with two ip addresses. I need to make the ip address that's currently the secondary the primary. How do I use the ifconfig command and primary option?
Thanks. (5 Replies)
Discussion started by: pmichner
5 Replies
4. IP Networking
HI All,
My interface card has failed.If i am giving the command to uplumb it i am getting an error.
ce401001: flags=219040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,FAILED,CoS> mtu 1500 index 3
inet 10.188.24.18 netmask ffffffc0 broadcast 10.188.24.63
# ifconfig... (2 Replies)
Discussion started by: sag71155
2 Replies
5. Shell Programming and Scripting
Hello All,
Can someone show me how to cat "only the IP address of e1000g0" using ifconfig -a.
i am trying to grep only the ip address (xx.xx.xx.xx) from the bunch of all other things like, broadcast address, IPV4, UP........and so on.
thanks (1 Reply)
Discussion started by: solaix14
1 Replies
6. Shell Programming and Scripting
I'm a newbie to linux, so pleases forgive me!
I would like to find a script that I could use to extract a dynamic ip from the ppp0 and set it as a variable to be used in IPTables
basically, if ppp0 ip address is 10.10.10.20, I would like a script that would set a var to 10.10.10.0. of... (9 Replies)
Discussion started by: speedy3k
9 Replies
7. IP Networking
I'm working on an AIX Unix LPAR (AIX 3.5 00C3C9904C00 as returned by uname -a)
I can access this box using telnet, port 22 using adress IP A and B
A=AA.AA.XX.XX and B=AA.AA.YYY.YYY
I can confirm these 2 are the same space, I can see
I can't find address B listed anywhere... so I wonder what... (1 Reply)
Discussion started by: Isax50
1 Replies
8. Solaris
hi,
I am trying to configure one of my interfaces, but after reboot - i lose the changes to the netmask & broadcast address.
I have added an entry in /etc/netmasks, but it doesnt pick up the new settings. any ideas - much appreciated.
before reboot:
eri0:... (3 Replies)
Discussion started by: badoshi
3 Replies
9. Shell Programming and Scripting
Hi
I am trying to create a script extracting the IP provided by ifconfig.
I tried with grep + awk but I am returned more than I need.
/sbin/ifconfig eth0 | grep "inet addr:" | awk '/inet addr:/ { print $2 }'
and returns
addr:10.15.1.64
How can I remove "addr:" string?... (9 Replies)
Discussion started by: manustone
9 Replies
10. Solaris
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
Discussion started by: Kjons76
3 Replies
BE(4) BSD Kernel Interfaces Manual BE(4)
NAME
be -- SPARC Fast Ethernet interface
SYNOPSIS
qec* at sbus? slot ? offset ?
be* at qec?
DESCRIPTION
The be interface provides access to the 10Mb/s and 100Mb/s (half duplex only) Ethernet networks. The be is found on the Sun 10/100 Mbit Eth-
ernet boards (Sun part number SUNW,501-2450).
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The be interface employs the address resolution
protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
The be is not capable of link autonegotiation, so a media type must be specified with ifconfig(8). The supported media types are:
media 100baseTX
Use 100Mbps, half duplex
media 10baseT
Use 10Mbps, half duplex
SEE ALSO
arp(4), ifmedia(4), inet(4), intro(4), netintro(4), sbus(4), ifconfig(8)
HISTORY
Support for the be first appeared in NetBSD 1.4.
BSD
March 31, 2004 BSD