Solaris 10 x86 Jumpstart w/o GUI Post: 302232507

9 More Discussions You Might Find Interesting

1. Solaris

Jumpstart on x86 client- prompt for CD2

Hi I just configured a jumpstart server for x86 and sparc clients. I don't use a dhcp server, so I configured /etc/ethers and did add_install_client to update /etc/bootparams. The sparc installation ist working, but the x86 installation stops after CD1 was successfully installed. What I did: I...

2. Solaris

Jumpstart Solaris 10 x86

I need a little help figuring out why my custom jumpstart network installation is dumping me to a manual install. I am trying to install Solaris 10 (unattended) over the wire from my jumpstart server to an HP Proliant DL380 server but I'm having difficulties with the unattended part. So, what...

3. Solaris

One time network boot of Jumpstart x86 client

I am trying to find an approach that has been effective for automating the installation of Solaris 10 x86 using Jumpstart technology. I have configured an Jumpstart server and a Solaris dhcp server with appropriate macros for passing the client information about its boot environment. The problem is...

4. Solaris

Jumpstart sparc client using x86 server.

Can I use a Jumpstart enviroment on x86 to install a sparc64 client? The idea is to install Solaris in an virtual environment (Sun Virtual Box) running on a pc (AMD), configure a Jumpstart server, and have a SUN Ultra 60 (sparc64) installed via the Jumpstart server. The SUN has no cdrom...

5. Solaris

Automate Solaris x86 Jumpstart

Hi All, Is there a possible way to fully automate Solaris x86 jumpstart or make the x86 jumpstart unattended? I'm currently checking the possible options on how can I do the x86 jumpstart to be kicked off during midnight. We have an automated jumpstart (start to run from midnight) for...

6. Solaris

Jumpstart Installation from X86 machine

Hi friends , i have on ultra 10 Sparc machine . Due to some problem my OS is fully corrupted , so i am planning to install again but my problem is the cd drive in Ultra 10 machine is not working. Now i am planning to use Jumpstart installation method to install my server. But i...

7. Solaris

custom jumpstart on x86 with DHCP/PXE goes into interactive mode

client boots fine, it gets the ip 192.168.0.10 and the bootfile. Then there is : SunOS 5.10 Version Generic_141445-09 32-bit" ... Configuring devices. Custom JumpStart Reading ZFS config: done Setting up Java. Please wait ... NOTE: Not enough memory for graphical installation. Graphical...

8. Solaris

Solaris x86 installation using jumpstart does not local boot ( boot from hdd)

I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD...

9. Solaris

Installing Solaris x86 using jumpstart does not set the hostname for the target

Installing Solaris x86 using jumpstart does not set the hostname for the target. Any idea where do we need to specify hostname to be set for jumpstart installation.

LEARN ABOUT NETBSD

urlphy

URL(4)							   BSD Kernel Interfaces Manual 						    URL(4)

NAME

     url -- Realtek RTL8150L USB Ethernet driver

SYNOPSIS

     url*    at uhub?
     urlphy* at mii?

DESCRIPTION

     The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.

     The url driver supports the following adapters:

	   CompUSA USBKR100
	   GreenHouse GH-USB100B
	   Melco Inc. LUA-KTX
	   Sitecom LN013

     For more information on configuring this device, see ifconfig(8).

DIAGNOSTICS

     url%d: watchdog timeout  A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
     transmission before a timeout expired.

     url%d: no memory for rx list  The driver failed to allocate an mbuf for the receiver ring.

SEE ALSO

     arp(4), mii(4), netintro(4), usb(4), ifconfig(8)

HISTORY

     The url device driver first appeared in NetBSD 1.6.

AUTHORS

     The url driver was written by Shingo WATANABE <nabe@nabechan.org>.

BSD
								September 18, 2006							       BSD