08-27-2008
Smt
Hi ,
Its a p550 server and I have migrated that server to aix 5.3 ml 7 but still when i run smtctl is give error comand not found.
10 More Discussions You Might Find Interesting
1. AIX
How do you turn SMT(symm multi threading).I think that is what it's called.:)
TIA
Mike (2 Replies)
Discussion started by: mcastill66
2 Replies
2. Solaris
HELP.....
How to enable and disable RSH in solaris 8 (4 Replies)
Discussion started by: gini
4 Replies
3. HP-UX
I'm working on a system to monitor a wide-range of Unix platforms, and I'd like to know if HP-UX has anything similar to AIX's SMT (simultaneous multithreading)? If there a way to separate an HP-UX CPU into multiple logical partitions which can then act as multiple CPUs?
Thanks in advance,
Dave (0 Replies)
Discussion started by: DaveZeltserman
0 Replies
4. Solaris
dear all
i want to enable the below logs can you help me
/var/adm/xferlog
/var/spool/uucp/.Admin
thanx you (0 Replies)
Discussion started by: murad.jaber
0 Replies
5. UNIX and Linux Applications
hi guyz i work as a system administrator for some organization(am a newbie). one of the solaris machines is loaded with the messenger server...all configured by a former administrator. my task was to create user accounts for the mail and calendar services and as i checked its not working .....i... (0 Replies)
Discussion started by: henokia4j
0 Replies
6. AIX
Hello everyone,
I installed AIX the other day (several times!) but I can't get XDMCP to work.
I remember from when I installed it the last time it worked out of the box.
So why doesn't it work now?
This is the error message I get:
XDMCP fatal error: Session failed Session 2 failed for... (3 Replies)
Discussion started by: Kotzkroete
3 Replies
7. SCO
edit: solution found
Auditing Quick Start and Compatibility Notes (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
8. UNIX for Dummies Questions & Answers
Why can I not use the enable command?
*sofiazoe* (2 Replies)
Discussion started by: anglenasalt
2 Replies
9. UNIX for Advanced & Expert Users
Hi Folks!
I am writing a script which changes lpfc.conf if there it has been setup on RHEL BOXes, do I need to put dracut -f for enabling it? I am not sure,
Can someone help! (6 Replies)
Discussion started by: nixhead
6 Replies
10. AIX
Hi,
I have a POWER8 server running in Processor Implementation Mode: POWER 7.
I have 2 LPAR's, both are capped with 4 cores.
One of them displays:
Shared-SMT-4
and the other:
Dedicated-SMT-4
What is the difference when running in capped mode?
Thanks (1 Reply)
Discussion started by: amitlib
1 Replies
FPA(4) BSD Kernel Interfaces Manual FPA(4)
NAME
fpa, fea, fta -- DEC FDDI interface driver
SYNOPSIS
fpa* at pci? dev ? function ?
fea* at eisa? slot ?
alpha and pmax
fta* at tc? slot ? offset ?
DESCRIPTION
Cards supported by the fpa, fea and fta device driver are:
DEFPA DEC PCI FDDI Controller
DEFEA DEC EISA FDDI Controller
DEFTA DEC TURBOchannel FDDI Controller
respectively. All variants of either controller are supported including the DAS and SAS configurations.
DIAGNOSTICS
fea%d: error: desired IRQ of %d does not match device's actual IRQ (%d) The device probe detected that the DEFEA board is configured for a
different interrupt than the one specified in the kernel configuration file.
fea%d: error: memory not enabled! ECU reconfiguration required The device probe found that no device memory had been configured on the
DEFEA. The DEFEA can be configured with no device memory, this driver requires a minimum of 1K device memory be set up. The ECU (EISA Con-
figuration Utility) will need to be run to change the settings.
SEE ALSO
arp(4), netintro(4), ifconfig(8)
AUTHORS
The fpa, fea and fta device driver and manual page were written by Matt Thomas.
BUGS
Normally, the device driver will not enable the reception of SMT frames. However if the IFF_LINK1 flag is set, the device driver will enable
the reception of SMT frames and pass them up to the Berkeley Packet Filter for processing.
BSD
March 13, 1995 BSD