Sponsored Content
Special Forums Hardware Filesystems, Disks and Memory Problem loading RedHat6.2 on Sun Sparcstation5 Post 29982 by FattyLumpkin on Tuesday 15th of October 2002 06:18:47 AM
Old 10-15-2002
Data Problem loading RedHat6.2 on Sun Sparcstation5

I have been trying to install RedHat6.2 for sparc on a Sparcstation5. After partitioning the hard drive, the system keeps hanging while trying to format the disk. I don't get any error messages to indicate what the problem is. Is there a way of checking the integrity of the hd from the boot prom? Better still, is there a way of formatting the h/d from the boot prom?
 

10 More Discussions You Might Find Interesting

1. Windows & DOS: Issues & Discussions

loading problem in XP help!!!!!!!!!!!

have a azuse mother borad 1600Mhz ram 512 hd 40gb will not install windows want to finish but will not take it! Is this a hard ware problem or a virus i use av norton 2002 and nod32 think got a virus not shure xp will not load any more (2 Replies)
Discussion started by: amicrawler2000
2 Replies

2. UNIX Desktop Questions & Answers

Red Hat loading problem

when i try to load Redhat 7.2 the screen gets all mished together as if it were a meltdown the book says its a prob with X but it dosnt really say what to do WINMe works fine i have a radeon 64 MB card 1 gig processor and 2 HDs on a Dell 1 GHZ how do i fix this ? (1 Reply)
Discussion started by: ASpin
1 Replies

3. IP Networking

Nework; how to configure under redhat6?

Hi all, im running a redhat 6 linux on an Laptop. I am unable to find the configuration file where i have to configure all the settings like ip address, netmast, broadcast and gateway. Every time at startup i have wrong settings of the network. Thx all for help! Best regards Frank (2 Replies)
Discussion started by: ortsvorsteher
2 Replies

4. Linux

Problem Loading Linux

I have Linux on an image in my cd-rom drive. I have previously loaded Windows XP but couldnt use it because I had already installed it on another PC - so I want to remove this and load Linux. I am fairly PC illiterate when it come to dos-commands and such... HELP!!! (1 Reply)
Discussion started by: Kyroq
1 Replies

5. Shell Programming and Scripting

Problem of Data Loading....

i am studying a script which is used for data loading. it has functions which deletes all the existing data before loading and then loads new fresh data. but i am stuck up at function Replace into table ( col 1,col 2....) Does this signify All Inserts. (1 Reply)
Discussion started by: ankitgupta
1 Replies

6. UNIX for Dummies Questions & Answers

LPAR Loading Problem

I'm having a major problem trying to load a LPAR. I've got through the HMC and shutdown and then activated the LPAR and it only gets to the Operator Panel Value of 0517. Now from some research I've found that this is to do with loading the rootvg. ( I think ) On the actual terminal all I get is... (0 Replies)
Discussion started by: KeesH
0 Replies

7. Solaris

Application Loading problem

I install a software xchm for opening chm files. I install software and also its required libraries. But when i start it; no GUI appears. Application got halt. Process name also appears in process list when i run top command. Appliation continously using cpu but no GUI appears. Please tell me... (7 Replies)
Discussion started by: mansoorulhaq
7 Replies

8. Linux

Problem in loading library

I am trying to run seagull tool. But when i start it following error shown |E|Unable to open library file error |A|STOP log Please help me how i can recover from it. (1 Reply)
Discussion started by: mansoorulhaq
1 Replies

9. UNIX for Advanced & Expert Users

OpenBoot Loading Problem

I am using a SunBlade 100 system and accidently set a new alias for keyboard, now when it start it gives the following error, The selected input device has no read routine. Keyboard not present using ttya for input and output. Now i cannot execute any commands on the OBP and i just gets... (3 Replies)
Discussion started by: sumwhriblong
3 Replies

10. UNIX for Advanced & Expert Users

Problem loading cpufreq module

I'd like to install cpufreq modules on my server . I tried sudo modprobe acpi-cpufreq but got the error FATAL: Error inserting acpi_cpufreq (/lib/modules/2.6.18-238.12.1.el5xen/kernel/arch/x86_64/kernel/cpufreq/acpi-cpufreq.ko): No such device cat /proc/cpuinfo gives this ... (11 Replies)
Discussion started by: vishwamitra
11 Replies
installboot(1M) 														   installboot(1M)

NAME
installboot - install bootblocks in a disk partition SYNOPSIS
installboot bootblk raw-disk-device The boot(1M) program, ufsboot, is loaded from disk by the bootblock program which resides in the boot area of a disk partition. The ufs boot objects are platform-dependent, and reside in the /usr/platform/platform-name/lib/fs/ufs directory. The platform name can be found using the -i option of uname(1). The installboot utility is a SPARC only program. It is not supported on the architecture. users should use installgrub(1M) instead. bootblk The name of the bootblock code. raw-disk-device The name of the disk device onto which the bootblock code is to be installed; it must be a character device which is read- able and writable. Naming conventions for a SCSI or IPI drive are c?t?d?s? and c?d?s? for an IDE drive. Example 1: Installing UFS Boot Block To install a ufs boot block on slice 0 of target 0 on controller 1 of the platform where the command is being run, use: example# installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk /dev/rdsk/c1t0d0s0 /usr/platform/platform-name/lib/fs/ufs directory where ufs boot objects reside. /platform/platform-name/ufsboot second level program to boot from a disk or CD See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ od(1), uname(1), boot(1M), init(1M), kadb(1M), kernel(1M), monitor(1M), reboot(1M), rpc.bootparamd(1M), init.d(4), attributes(5) WARNINGS
The installboot utility fails if the bootblk or openfirmware files do not exist or if the raw disk device is not a character device. 11 Apr 2005 installboot(1M)
All times are GMT -4. The time now is 01:29 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy