Hi,
i would like to enable all operations/connections to use a proxy server in a redhat server ,
witch file should i config to get this for all conections ....
Thanks (0 Replies)
hi everyone
does anybodey know an 802.1x open source authenticator?
i found hostpad and open1x but since im so so so new to freeBSD i do NOT know how to configure and use them ? can you help me please ?
thanks a lot ... (1 Reply)
hi everyone
does anybodey know an 802.1x open source authenticator?
i found hostpad and open1x but since im so so so new to freeBSD i do NOT know how to configure and use them ? can you help me please ?
thanks a lot ... (0 Replies)
I'm new to networking world. So please bear with me.
My Questions:
1. How do we send TCP/IP in a 802.3 frame? My understanding is that we have to incorporate the 802.3 LLC layer. The DSAP and SSAP in the LLC layer will provide information of the type of data inside the Information field of... (0 Replies)
My question is such:
I want to control the bandwidth of my users and cap there speed on the network. I was told by a Cisco rep that it is better to police or control the bandwidth at the switch and not via the router. It that the correct place to control bandwidth at the switch or would it be... (0 Replies)
I have a server I would like to disable 802.3x flow control on. The host is Linux (CentOS 4.4 x86_64 w/ 2.6.9-42.0.3.EL kernel,) and I'm using the ns83820 driver for the ethernet interface in question.
I've tried looking at the driver parameters (modinfo ns83820) and using ethtool (ethtool -a... (0 Replies)
ATU(4) BSD Kernel Interfaces Manual ATU(4)NAME
atu -- Atmel at76c50x 802.11B wireless network interfaces
SYNOPSIS
atu* at uhub? port ?
DESCRIPTION
The atu driver provides support for wireless network adapters based around the Atmel at76c503, at76c503a, at76c505, and at76c505a USB
chipsets.
Supported features include 802.11 and 802.3 frames, power management, BSS, IBSS, ad-hoc, and host-based access point mode.
The atu driver encapsulates all IP and ARP traffic as 802.11 frames, however it can receive either 802.11 or 802.3 frames. Transmit speed is
selectable between 1Mbps fixed, 2Mbps fixed, 2Mbps with auto fallback, 5.5Mbps, 8Mbps, or 11Mbps depending on your hardware.
Four different radio chipsets are used along with the device, each requiring a different firmware.
By default, the atu driver configures the card for BSS operation (aka infrastructure mode). This mode requires the use of an access point
(base station).
For more information on configuring this device, see ifconfig(8).
The following devices are among those supported by the atu driver:
Acer Peripherals AWL400
AcerP AWL-300
Aincomm AWU2000B
Atmel 2662W-V4
Atmel BW002
Atmel DWL-120
Atmel WL-1330
Belkin F5D6050
Geowave GW-US11S
Linksys WUSB11
Linksys WUSB11-V28
Ovislink AirLive
SMC 2662W-AR
SEE ALSO arp(4), ifmedia(4), intro(4), netintro(4), usb(4), ifconfig(8), wiconfig(8)AUTHORS
The atu driver was written by Daan Vreeken and ported to OpenBSD by Theo de Raadt and David Gwynne. The OpenBSD driver was then ported to
NetBSD by Jesse Off <joff@NetBSD.org>.
BSD January 23, 2005 BSD