Doubt with irq handler.......


 
Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers Doubt with irq handler.......
# 8  
Old 01-25-2010
Like I already said, if your interrupt trigger is triggering interrupts without a handler your kernel should be spewing "nobody cared" messages like mad. Your squarewave isn't actually triggering interrupts, whether your driver works or not.

You may need to read more on the ISA specification to see how to properly trigger an interrupt... AFAIK you need to bring the relevant INT line low then wait for an acknowledge or it goes nowhere.

Last edited by Corona688; 01-25-2010 at 11:41 AM..
# 9  
Old 01-25-2010
Quote:
Originally Posted by Corona688
You may need to read more on the ISA specification to see how to properly trigger an interrupt.
Hello,

You are right, it is better for me read more about ISA BUS.
I do not want to disturb anybody with problems if I do not understand what is my problem.

Anyway, Thank you very much Corona688 for your help.

Best regards.
I
 
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Programming

Serial port signal(IRQ) handler (using C)

Hello, I'm writing some serial(UART) handler but have stuck on few issues, maybe anyone can help to show me what I'm doing wrong. Basically I'm intending to write serial RX signal handler. Application receives defined packages of data over serial which contains header and payload. Handler... (3 Replies)
Discussion started by: Lauris_k
3 Replies

2. Hardware

IRQ and Number of Devices

Hello everyone. I feel that I'm about to answer my own question, but I just want to be sure that I'm right. I know computers all use, at a very low level, the IRQ system of interrupting the CPU when it needs something. My questions are as follows: 1. Does the device in question, say.. a mouse,... (1 Reply)
Discussion started by: Lost in Cyberia
1 Replies

3. Programming

What is unbalanced IRQ?

------------------------ WARNING: at kernel/irq/manage.c:225 __enable_irq+0x3b/0x57() Unbalanced enable for IRQ 4 Modules linked in: svsknfdrvr Pid: 634, comm: ash Tainted: G W 2.6.28 #1 Call Trace: warn_slowpath+0x76/0x8d profile_tick+0x2d/0x57 irq_exit+0x32/0x34 ... (3 Replies)
Discussion started by: dragonpoint
3 Replies

4. Linux

A question with respect to IRQ distribution

Hi all, I am a Linux newbie in kernel development. In class I was asked a question about IRQ distribution as followed. IRQs can be distributed among the available CPUs (in a multiple-CPU system) in two ways: (1) Static distribution The IRQ signal is delivered to the local APICs listed... (2 Replies)
Discussion started by: sunnyhay
2 Replies

5. SCO

IRQ conflict between USB and NIC SCO 5.0.7

I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port. After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded. As both USB and NIC driver are essential... (0 Replies)
Discussion started by: vikramviky
0 Replies

6. UNIX for Advanced & Expert Users

IRQ priority in FC9

Hi, I want to increase IRQ4 priority to maximum in Fedora core 9 (kernel version 2.6.25.11-97).If anybody knows plz help me.... I will be very thankful .. regards, Raj (0 Replies)
Discussion started by: rajuprade
0 Replies

7. UNIX for Dummies Questions & Answers

irq complication

hi, i looked around already and had no luck finding anything. Im trying ot install a wpc11v3 linksys wireless card, and i have been for about a week now. :mad: Im near certain i have figured out my problem. When i plug in my card while knoppix is running, it crashes. When i plug it into... (0 Replies)
Discussion started by: jestra
0 Replies

8. UNIX for Dummies Questions & Answers

usb - deleting (irq)

FreeBSD 4.5 i installed my sound drivers (which are onboard) with the following lines in my kernel device pcm options PNPBIOS then cd /dev sh MAKEDEV snd0 output from cat /dev/sndstat show the devicedriver (correct one) ok this works nice untill i enter my kde and want to play a... (1 Reply)
Discussion started by: termiEEE
1 Replies

9. UNIX for Dummies Questions & Answers

forcing irq on PCMCIA card

ENV: linux Version: Mandrake 8.1, PCMCIA card: longshine lcs-8534TB. (supported according the PCMCIA docs) laptop is P-II lifetec /etc/sysconfig/pcmcia: PCMCIA=yes PCIC=i82365 ( found via probe -m ) PCIC_OPTS="cs_irq=11 pci_irq_list=11,11 do_scan=0" ( you see i want to force irq 11 )... (3 Replies)
Discussion started by: progressdll
3 Replies

10. UNIX for Dummies Questions & Answers

irq

where can i find the i/o and irq's in mandrake 8 help lost :D (2 Replies)
Discussion started by: RYRY46D9
2 Replies
Login or Register to Ask a Question