How to identifying the network card ?

10 More Discussions You Might Find Interesting

1. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101...

2. Hardware

Identifying Network Ports

OK, so I have a real dumb question, but I am desperate for an answer. If my Sun machine shows the following out put. root@xxxx:/# egrep network /etc/path_to_inst "/pci@1f,0/pci@1,1/network@c,1" 0 "eri" "/pci@1f,0/pci@1,1/network@5,1" 1 "eri" Does that indicate that there is one eri...

3. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see...

4. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated.

5. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and...

6. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byte��link up...

7. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of...

8. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But...

9. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out.

10. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the...

LEARN ABOUT DEBIAN

bt-network

bt-network(1)							    bluez-tools 						     bt-network(1)

NAME

       bt-network - a bluetooth network manager

SYNOPSIS

       bt-network [OPTION...]

       Help Options:
	 -h, --help

       Application Options:
	 -a, --adapter=<name|mac>
	 -c, --connect <name|mac> <uuid>
	 -s, --server <gn|panu|nap> <brige>

DESCRIPTION

       This utility is used to manage network services (client/server).  All servers will be automatically unregistered when the application
       terminates.

OPTIONS

       -h, --help
	   Show help

       -a, --adapter <name|mac>
	   Specify adapter to use by his Name or MAC address
	   (if this option does not defined - default adapter used)

       -c, --connect <name|mac> <uuid>
	   Connect to the network device and return the network interface
	   name, uuid can be either one of "gn", "panu" or "nap"

       -s, --server <gn|panu|nap> <brige>
	   Register server for the provided UUID, every new connection to
	   this server will be added the bridge interface

AUTHOR

       Alexander Orlenko <zxteam@gmail.com>.

SEE ALSO

       bt-adapter(1) bt-agent(1) bt-audio(1) bt-device(1) bt-input(1) bt-monitor(1) bt-serial(1)

								    2010-11-22							     bt-network(1)

Solaris