10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Dear All,
I am trying to config a sys mail message on solaris 10.
I am doing the following commands but it dose not work with me;
#touch /var/mail-test
#vi /etc/syslog.cong
local0.notice /var/mail-test
#svcadm disable svcs:/system/system-log:default
#svcadm enable... (1 Reply)
Discussion started by: ahmedamer12
1 Replies
2. Solaris
I did a sys-unconfig to change the domainname, Ip, subnet, hostname, and pretty much everything else that sys-unconfig handles. Upon reboot, it is toast. I did this all without the network cable plugged in.
The following shows up on console:
login: pam_unix_cred: cannot load ttyname Error 0
... (3 Replies)
Discussion started by: adelsin
3 Replies
3. UNIX for Advanced & Expert Users
Hi All!
I'm running "Solaris 10 10/08 s10s_u6wos_07b SPARC" on M5000.
I ran sys-unconfig and after the machine rebooted the system did not prompt me for configuration info (system name, ip address, etc). I have also modified /etc/.sysIDtool.state changing all "1" to "0" and touch... (1 Reply)
Discussion started by: bluescreen
1 Replies
4. UNIX for Dummies Questions & Answers
ok,
Newbie here.....
I just installed this solaris 10 for a class I'm taking. We couldn't figure out how to change the IP so we were told to just do it from the sys-uncofig process. Well, after I did that, I lost the GUI witch isn't all that bad cuz I want to learn the cli anyways, but I keep... (1 Reply)
Discussion started by: moesays
1 Replies
5. Solaris
Hi there,
We are trying to move our Sun Solaris 10 servers to new location (different state); the subnets will be changing ofcourse and so will the IP addresses; we plan to change hostname too.
Questions:
1)If we perform sys-unconfig will the current installed application/data be lost? If so,... (4 Replies)
Discussion started by: deedee
4 Replies
6. Solaris
Hi,
I performed a sys-unconfig on a solaris 10 server twice and it did not ask for a new hostname. I did a fresh install. most of the time I have experienced that it asks for a new hostname. what happened?
I know I could have edited some files but I prefer not to.
thanks in advance,
~jv (3 Replies)
Discussion started by: jvmagic
3 Replies
7. Solaris
hi experts,
i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display :
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies
8. Solaris
hi expert,
i had reinstall the sun v890 server solaris 8 and also do mirroring, i had configure the network for the server (hostname.eri0,hosts,netmasks,nodename,etc) after i reboot get and error messages below :
Setting default IPv4 interface for multicast: add net 224.0/4: gateway... (5 Replies)
Discussion started by: bucci
5 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I have a SPARCstation 10 with SunOS 5.6
This erlier was in a network and now I have it at home to make a webserver.
At fist there was NIS and things left from erlier. So the "Console login:" newer appered only the white window with sun logo topleft and some text info.
I made... (14 Replies)
Discussion started by: roing
14 Replies
10. IP Networking
I am running Solaris 8 and I have problem with configuration of the network after running sys-unconfig command:
- I ran "sys-unconfig" command then the system reboot to "ok" prompt. I did a "boot disk" command and the system reboot
- I lost all system info including host name and all addresses... (3 Replies)
Discussion started by: rachael
3 Replies