10-11-2006
If you aren't using DNS at all, then your issue will be with Sendmail. Sendmail by default uses DNS. You can look at
Sendmail's FAQ for info on setting up sendmail not to use DNS.
10 More Discussions You Might Find Interesting
1. IP Networking
I am running Solaris 8 and I have problem with configuration of the network after running sys-unconfig command:
- I ran "sys-unconfig" command then the system reboot to "ok" prompt. I did a "boot disk" command and the system reboot
- I lost all system info including host name and all addresses... (3 Replies)
Discussion started by: rachael
3 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I have a SPARCstation 10 with SunOS 5.6
This erlier was in a network and now I have it at home to make a webserver.
At fist there was NIS and things left from erlier. So the "Console login:" newer appered only the white window with sun logo topleft and some text info.
I made... (14 Replies)
Discussion started by: roing
14 Replies
3. Solaris
hi expert,
i had reinstall the sun v890 server solaris 8 and also do mirroring, i had configure the network for the server (hostname.eri0,hosts,netmasks,nodename,etc) after i reboot get and error messages below :
Setting default IPv4 interface for multicast: add net 224.0/4: gateway... (5 Replies)
Discussion started by: bucci
5 Replies
4. Solaris
hi experts,
i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display :
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies
5. Solaris
Hi,
I performed a sys-unconfig on a solaris 10 server twice and it did not ask for a new hostname. I did a fresh install. most of the time I have experienced that it asks for a new hostname. what happened?
I know I could have edited some files but I prefer not to.
thanks in advance,
~jv (3 Replies)
Discussion started by: jvmagic
3 Replies
6. Solaris
Hi there,
We are trying to move our Sun Solaris 10 servers to new location (different state); the subnets will be changing ofcourse and so will the IP addresses; we plan to change hostname too.
Questions:
1)If we perform sys-unconfig will the current installed application/data be lost? If so,... (4 Replies)
Discussion started by: deedee
4 Replies
7. UNIX for Dummies Questions & Answers
ok,
Newbie here.....
I just installed this solaris 10 for a class I'm taking. We couldn't figure out how to change the IP so we were told to just do it from the sys-uncofig process. Well, after I did that, I lost the GUI witch isn't all that bad cuz I want to learn the cli anyways, but I keep... (1 Reply)
Discussion started by: moesays
1 Replies
8. UNIX for Advanced & Expert Users
Hi All!
I'm running "Solaris 10 10/08 s10s_u6wos_07b SPARC" on M5000.
I ran sys-unconfig and after the machine rebooted the system did not prompt me for configuration info (system name, ip address, etc). I have also modified /etc/.sysIDtool.state changing all "1" to "0" and touch... (1 Reply)
Discussion started by: bluescreen
1 Replies
9. Solaris
I did a sys-unconfig to change the domainname, Ip, subnet, hostname, and pretty much everything else that sys-unconfig handles. Upon reboot, it is toast. I did this all without the network cable plugged in.
The following shows up on console:
login: pam_unix_cred: cannot load ttyname Error 0
... (3 Replies)
Discussion started by: adelsin
3 Replies
10. UNIX for Dummies Questions & Answers
Dear All,
I am trying to config a sys mail message on solaris 10.
I am doing the following commands but it dose not work with me;
#touch /var/mail-test
#vi /etc/syslog.cong
local0.notice /var/mail-test
#svcadm disable svcs:/system/system-log:default
#svcadm enable... (1 Reply)
Discussion started by: ahmedamer12
1 Replies
LEARN ABOUT MOJAVE
mail::dkim::dns
Mail::DKIM::DNS(3) User Contributed Perl Documentation Mail::DKIM::DNS(3)
NAME
Mail::DKIM::DNS - performs DNS queries for Mail::DKIM
DESCRIPTION
This is the module that performs DNS queries for Mail::DKIM.
CONFIGURATION
This module has a couple configuration settings that the caller may want to use to customize the behavior of this module.
$Mail::DKIM::DNS::TIMEOUT
This global variable specifies the maximum amount of time (in seconds) to wait for a single DNS query to complete. The default is 10.
Mail::DKIM::DNS::resolver()
Use this global subroutine to get or replace the instance of Net::DNS::Resolver that Mail::DKIM uses. If set to undef (the default), then a
brand new default instance of Net::DNS::Resolver will be created the first time a DNS query is needed.
You will call this subroutine if you want to specify non-default options to Net::DNS::Resolver, such as different timeouts, or to enable
use of a persistent socket. For example:
# first, construct a custom DNS resolver
my $res = Net::DNS::Resolver->new(
udp_timeout => 3, tcp_timeout => 3, retry => 2,
);
$res->udppacketsize(1240);
$res->persistent_udp(1);
# then, tell Mail::DKIM to use this resolver
Mail::DKIM::DNS::resolver($res);
Mail::DKIM::DNS::enable_EDNS0()
This is a convenience subroutine that will construct an appropriate DNS resolver that uses EDNS0 (Extension mechanisms for DNS) to support
large DNS replies, and configure Mail::DKIM to use it. (As such, it should NOT be used in conjunction with the resolver() subroutine
described above.)
Mail::DKIM::DNS::enable_EDNS0();
Use of EDNS0 is recommended, since it reduces the need for falling back to TCP when dealing with large DNS packets. However, it is not
enabled by default because some Internet firewalls which do deep inspection of packets are not able to process EDNS0-enabled packets. When
there is a firewall on a path to a DNS resolver, the EDNS0 feature should be specifically tested before enabling.
AUTHOR
Jason Long, <jlong@messiah.edu>
COPYRIGHT AND LICENSE
Copyright (C) 2006-2007, 2012-2013 by Messiah College
This library is free software; you can redistribute it and/or modify it under the same terms as Perl itself, either Perl version 5.8.6 or,
at your option, any later version of Perl 5 you may have available.
perl v5.18.2 2013-02-07 Mail::DKIM::DNS(3)