10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Hi Experts,
I wanted to extend a veritas file system which is running on veritas cluster and mounted on node2 system.
#hastatus -sum
-- System State Frozen
A node1 running 0
A node2 running 0
-- Group State
-- Group System Probed ... (1 Reply)
Discussion started by: Skmanojkum
1 Replies
2. Linux
When installing Linux, I choose some default setting to use all the disk space.
My server has a single internal 250Gb SCSI disk. By default the install appears to have created 3 logical volumes
lv_root, lv_home and lv_swap.
fdisk -l shows the following
lab3.nms:/dev>fdisk -l
Disk... (2 Replies)
Discussion started by: jimthompson
2 Replies
3. Solaris
Hi,
More a Sun T5220 problem then a Solaris 10 problem, but perhaps someone had a similar issue.
For starters the output with 1 disk in slot 0 of the server.
It points to PhyNum 5, where I would expect PhyNum 0.
{0} ok probe-scsi
MPT Version 1.05, Firmware Version 1.22.00.00
Target... (2 Replies)
Discussion started by: ejdv
2 Replies
4. Solaris
Hi,
I`m on SunFire480R with Solaris 10. Disk in rootdg group failed, so it was replaced. However, I cannot make Veritas initalise the replaced disk:
# vxdctl enable
# vxdisk list c1t0d0s2
Device: c1t0d0s2
devicetag: c1t0d0
type: auto
flags: online error private autoconfig... (1 Reply)
Discussion started by: masloff
1 Replies
5. UNIX for Dummies Questions & Answers
People i have an a storage i create two virtual disk 1 y 2.
In the virtual disk 1 i configure 8 volumes and in the Vd2 configure 5 volumes.
Now i want to create a disk group called Prod2 y Dev2 but when i go to vxdiskadm and i choose add disk o encapusalte when i press list to list the disk... (0 Replies)
Discussion started by: enkei17
0 Replies
6. AIX
Hello guys,
It would be so nice of you if someone can provide me with these informations.
1) My SAN group assigned 51G of LUN space to the VIO server.I ran cfgdev to discover the newly added LUN. Unfortunately most of the disks that are in VIO server is 51G. How would I know which is the newly... (3 Replies)
Discussion started by: solaix14
3 Replies
7. AIX
We have a frame the uses 2 vios that assign disk storage to LPAR's. We have a LPAr with multiple disk and I want to know how do I tell which vio is serving the disk. For example the LPAr has hdisk 0, 1, 2, 3 all the same size. I want to know which vio is serving hdisk0, 1. (4 Replies)
Discussion started by: daveisme
4 Replies
8. Solaris
Dear Solaris Experts,
I am a bit confused about OpenSolaris Hard Drive device mapping. On RedHat Linux based system, an IDE on first channel master drive is mapped as /dev/hda, first channel slave drive will be /dev/hdb, etc.
For (Open)Solaris systems I found it as /dev/rdsk/c3d0p0 :
... (0 Replies)
Discussion started by: Zepiroth
0 Replies
9. Solaris
I have a bogus disk that keeps showing up as failed from vxdisk list
- - disk hpdg failed was:c2t0d11s2
There isnt any c2 devices on the system:
# ls /dev/dsk/c2*
/dev/dsk/c2*: No such file or directory
# ls /dev/rdsk/c2*
/dev/rdsk/c2*: No such file or... (3 Replies)
Discussion started by: kiem
3 Replies
10. Filesystems, Disks and Memory
I've had a VXFS filesystem get corrupted and now it won't mount.
Can I run a fsck -y on the raw disk device or should something be
done within veritas? Veritas does not see the disk at the moment. (2 Replies)
Discussion started by: ozzmosiz
2 Replies
groups(1) General Commands Manual groups(1)
NAME
groups - Displays your group membership
SYNOPSIS
groups [user]
DESCRIPTION
The groups command writes to standard output the groups to which you or the specified user belong. The Tru64 UNIX operating system allows
a user to belong to many different groups at the same time.
Your primary group is specified in the /etc/passwd file. Once you are logged in, you can change your active group with the newgrp shell
command (see sh). When you create a file, its group ID is that of your active group.
Other groups that you belong to are specified in the /etc/group file. If you belong to more than one group, you can access files belonging
to any of those groups without changing your primary group ID. These are called your concurrent groups.
NOTES
The /etc/passwd and /etc/group files must be on the same node.
EXAMPLES
To determine your group membership, enter: groups
The groups to which you belong will be displayed. For example: devel prod
FILES
Contains group information. Contains user information.
SEE ALSO
Commands: csh(1), ksh(1), sh(1)
Functions: initgroups(3), setgroups(2)
groups(1)
