Oracle's StorageTek T10000C tape drive is the first to offer the StorageTek Search Accelerator (SSA). SSA uses tape drive hardware to speed data searches, and offload that processing requirement from other data center resources.
Hi everyone,
I have a big problem and i hope u can help me. I have brand new sun server X4-2 with Solaris 10-update 10. I have to install oracle StorageTek but there is no guide or help on the internet. Can anybody help me?
CU (1 Reply)
Hi,
I recently got StoragaTek 2500 and I would like to connect it to my solaris machine, since I don't have much experience with storages, could someone point me how to do so, how can i present disks from storage on my solaris os? (everything is already connected)
thanks in advance (1 Reply)
I believe this may be a difference in GTK+-2.0 and GTK+-3.0. I followed this tutorial and ended up with this error:
# gcc -Wall -g mnemonics.c -o mnemonics `pkg-config --cflags gtk+-3.0` `pkg-config --libs gtk+-3.0`
mnemonics.c: In function ‘main':
mnemonics.c:44:61: error: ‘GDK_q' undeclared... (3 Replies)
Hello all !
I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server.
I... (2 Replies)
Hi,
I installed DirectFb on fedora 7, the machine has a Nvidia graphics card. The installation was successful and I can play the examples provided by the Direct fb website, but, I find that the accelarator is not getting recognised. when I do "fbset -i", the details shown are as below, it gives... (0 Replies)
I had been using a modem installed on a Digi accelerator port to dial in to an SCO open server r5 server. On monday it quit working and I realy don't know how it was installed and configured. I have tested the modem on a PC and it works. The port the modem is connected to is ttyB06 and I have... (1 Reply)
HT(4) Kernel Interfaces Manual HT(4)NAME
ht - TM-03/TE-16,TU-45,TU-77 MASSBUS magtape interface
SYNOPSIS
/sys/conf/SYSTEM:
NHT ht_drives # TE16, TU45, TU77
/etc/dtab:
#Name Unit# Addr Vector Br Handler(s) # Comments
ht ? 172440 224 5 htintr # tu 16 massbus tape
major device number(s):
raw: 6
block: 0
minor device encoding:
bits 0003 specify HT drive
bit 0004 specifies no-rewind operation
bit 0010 specifies 1600BPI recording density instead of 800BPI
DESCRIPTION
The tm-03/transport combination provides a standard tape drive interface as described in mtio(4). All drives provide both 800 and 1600
bpi; the TE-16 runs at 45 ips, the TU-45 at 75 ips, while the TU-77 runs at 125 ips and autoloads tapes.
FILES
/dev/MAKEDEV script to create special files
/dev/MAKEDEV.local script to localize special files
SEE ALSO mt(1), tar(1), tp(1), mtio(4), tm(4), ts(4), dtab(5), autoconfig(8)DIAGNOSTICS
tu%d: no write ring. An attempt was made to write on the tape drive when no write ring was present; this message is written on the termi-
nal of the user who tried to access the tape.
tu%d: not online. An attempt was made to access the tape while it was offline; this message is written on the terminal of the user who
tried to access the tape.
tu%d: can't change density in mid-tape. An attempt was made to write on a tape at a different density than is already recorded on the
tape. This message is written on the terminal of the user who tried to switch the density.
tu%d: hard error bn%d er=%b ds=%b. A tape error occurred at block bn; the ht error register and drive status register are printed in
octal with the bits symbolically decoded. Any error is fatal on non-raw tape; when possible the driver will have retried the operation
which failed several times before reporting the error.
BUGS
If any non-data error is encountered on non-raw tape, it refuses to do anything more until closed.
The system should remember which controlling terminal has the tape drive open and write error messages to that terminal rather than on the
console.
3rd Berkeley Distribution January 28, 1988 HT(4)