Unix/Linux Go Back    


NetBSD 6.1.5 - man page for ping (netbsd section 8)

Linux & Unix Commands - Search Man Pages
Man Page or Keyword Search:   man
Select Man Page Set:       apropos Keyword Search (sections above)


PING(8) 			   BSD System Manager's Manual				  PING(8)

NAME
     ping -- send ICMP ECHO_REQUEST packets to network hosts

SYNOPSIS
     ping [-aCDdfLnoPQqRrv] [-c count] [-E policy] [-g gateway] [-h host] [-I srcaddr]
	  [-i interval] [-l preload] [-p pattern] [-s packetsize] [-T ttl] [-t tos] [-w deadline]
	  host

DESCRIPTION
     ping uses the ICMP protocol's mandatory ECHO_REQUEST datagram to elicit an ICMP
     ECHO_RESPONSE from a host or gateway.  ECHO_REQUEST datagrams (``pings'') have an IP and
     ICMP header, followed by a ``struct timespec'' and then an arbitrary number of ``pad'' bytes
     used to fill out the packet.  The options are as follows:

     -a      Emit an audible beep (by sending an ascii BEL character to the standard error out-
	     put) after each non-duplicate response is received.  This is disabled for flood
	     pings as it would probably cause temporary insanity.

     -C      Send timestamps in compat format; two 32 bit words in little endian format, the
	     first one representing seconds, and the second one representing microseconds.

     -c count
	     Stop after sending (and waiting the specified delay to receive) count ECHO_RESPONSE
	     packets.

     -D      Set the Don't Fragment bit in the IP header.  This can be used to determine the path
	     MTU.

     -d      Set the SO_DEBUG option on the socket being used.

     -E policy
	     Use IPsec policy specification string policy for packets.	For the format of speci-
	     fication string, please refer ipsec_set_policy(3).  Please note that this option is
	     same as -P in KAME/FreeBSD and KAME/BSDI (as -P was already occupied in NetBSD).

     -f      Flood ping.  Outputs packets as fast as they come back or one hundred times per sec-
	     ond, whichever is more.  For every ECHO_REQUEST sent a period ``.'' is printed,
	     while for every ECHO_REPLY received a backspace is printed.  This provides a rapid
	     display of how many packets are being dropped.  Only the super-user may use this
	     option.  This can be very hard on a network and should be used with caution.

     -g gateway
	     Use Loose Source Routing to send the ECHO_REQUEST packets via gateway.

     -h host
	     is an alternate way of specifying the target host instead of as the last argument.

     -I srcaddr
	     Set the source IP address to srcaddr which can be a hostname or an IP number.  For
	     multicast datagrams, it also specifies the outgoing interface.

     -i interval
	     Wait interval seconds between sending each packet.  The default is to wait for one
	     second between each packet, except when the -f option is used the wait interval is
	     0.01 seconds.

     -L      Disable loopback when sending to multicast destinations, so the transmitting host
	     doesn't see the ICMP requests.

     -l preload
	     If preload is specified, ping sends that many packets as fast as possible before
	     falling into its normal mode of behavior.	Only the super-user may use this option.

     -n      Numeric output only.  No attempt will be made to look up symbolic names for host
	     addresses.

     -o      Exit successfully after receiving one reply packet.

     -P      Use a pseudo-random sequence for the data instead of the default, fixed sequence of
	     incrementing 8-bit integers.  This is useful to foil compression on PPP and other
	     links.

     -p pattern
	     You may specify up to 16 ``pad'' bytes to fill out the packet you send.  This is
	     useful for diagnosing data-dependent problems in a network.  For example, ``-p ff''
	     will cause the sent packet to be filled with all ones.

     -Q      Do not display responses such as Network Unreachable ICMP messages concerning the
	     ECHO_REQUESTs sent.

     -q      Quiet output.  Nothing is displayed except the summary lines at startup time and
	     when finished.

     -R      Record Route.  Includes the RECORD_ROUTE option in the ECHO_REQUEST packet and dis-
	     plays the route buffer on returned packets.  This should show the path to the target
	     host and back, which is especially useful in the case of asymmetric routing.  Note
	     that the IP header is only large enough for nine such addresses, and only seven when
	     using the -g option.  This is why it was necessary to invent traceroute(8).  Many
	     hosts ignore or discard this option.

     -r      Bypass the normal routing tables and send directly to a host on an attached network.
	     If the host is not on a directly-attached network, an error is returned.  This
	     option can be used to ping a local host through an interface that has no route
	     through it (e.g., after the interface was dropped by routed(8)).

     -s packetsize
	     Specifies the number of data bytes to be sent.  The default is 56, which translates
	     into 64 ICMP data bytes when combined with the 8 bytes of ICMP header data.  The
	     maximum allowed value is 65467 bytes.

     -T ttl  Use the specified time-to-live.

     -t tos  Use the specified hexadecimal type of service.

     -v      Verbose output.  ICMP packets other than ECHO_RESPONSE that are received are listed.

     -w deadline
	     Specifies a timeout, in seconds, before ping exits regardless of how many packets
	     have been sent or received.

     When using ping for fault isolation, it should first be run on the local host, to verify
     that the local network interface is up and running.  Then, hosts and gateways further and
     further away should be ``pinged''.

     Round-trip times and packet loss statistics are computed.	If duplicate packets are
     received, they are not included in the packet loss calculation, although the round trip time
     of these packets is used in calculating the minimum/average/maximum round-trip time numbers.

     When the specified number of packets have been sent (and received) or if the program is ter-
     minated with a SIGINT, a brief summary is displayed.  The summary information can be dis-
     played while ping is running by sending it a SIGINFO signal (see the ``status'' argument for
     stty(1) for more information).

     ping continually sends one datagram per second, and prints one line of output for every
     ECHO_RESPONSE returned.  On a trusted system with IP Security Options enabled, if the net-
     work idiom is not MONO, ping also prints a second line containing the hexadecimal represen-
     tation of the IP security option in the ECHO_RESPONSE.  If the -c count option is given,
     only that number of requests is sent.  No output is produced if there is no response.
     Round-trip times and packet loss statistics are computed.	If duplicate packets are
     received, they are not included in the packet loss calculation, although the round trip time
     of these packets is used in calculating the minimum/average/maximum round-trip time numbers.
     When the specified number of packets have been sent (and received) or if the program is ter-
     minated with an interrupt (SIGINT), a brief summary is displayed.	When not using the -f
     (flood) option, the first interrupt, usually generated by control-C or DEL, causes ping to
     wait for its outstanding requests to return.  It will wait no longer than the longest round
     trip time encountered by previous, successful pings.  The second interrupt stops ping imme-
     diately.

     This program is intended for use in network testing, measurement and management.  Because of
     the load it can impose on the network, it is unwise to use ping during normal operations or
     from automated scripts.

ICMP PACKET DETAILS
     An IP header without options is 20 bytes.	An ICMP ECHO_REQUEST packet contains an addi-
     tional 8 bytes worth of ICMP header followed by an arbitrary amount of data.  When a
     packetsize is given, this indicated the size of this extra piece of data (the default is
     56).  Thus the amount of data received inside of an IP packet of type ICMP ECHO_REPLY will
     always be 8 bytes more than the requested data space (the ICMP header).

     If the data space is at least sizeof(struct timespec) (16) large, ping uses the first
     sizeof(struct timespec) bytes to include a timestamp to compute round trip times.	Otherwise
     if the data space is at least eight bytes large (or the -C flag is specified), ping uses the
     first eight bytes of this space to include a timestamp to compute round trip times.  If
     there are not enough bytes of pad no round trip times are given.

DUPLICATE AND DAMAGED PACKETS
     ping will report duplicate and damaged packets.  Duplicate packets should never occur, and
     seem to be caused by inappropriate link-level retransmissions.  Duplicates may occur in many
     situations and are rarely (if ever) a good sign, although the presence of low levels of
     duplicates may not always be cause for alarm.

     Damaged packets are obviously serious cause for alarm and often indicate broken hardware
     somewhere in the ping packet's path (in the network or in the hosts).

TRYING DIFFERENT DATA PATTERNS
     The (inter)network layer should never treat packets differently depending on the data con-
     tained in the data portion.  Unfortunately, data-dependent problems have been known to sneak
     into networks and remain undetected for long periods of time.  In many cases the particular
     pattern that will have problems is something that doesn't have sufficient ``transitions'',
     such as all ones or all zeros, or a pattern right at the edge, such as almost all zeros.  It
     isn't necessarily enough to specify a data pattern of all zeros (for example) on the command
     line because the pattern that is of interest is at the data link level, and the relationship
     between what you type and what the controllers transmit can be complicated.

     This means that if you have a data-dependent problem you will probably have to do a lot of
     testing to find it.  If you are lucky, you may manage to find a file that either can't be
     sent across your network or that takes much longer to transfer than other similar length
     files.  You can then examine this file for repeated patterns that you can test using the -p
     option of ping.

TTL DETAILS
     The TTL value of an IP packet represents the maximum number of IP routers that the packet
     can go through before being thrown away.  In current practice you can expect each router in
     the Internet to decrement the TTL field by exactly one.

     The TCP/IP specification states that the TTL field for TCP packets should be set to 60, but
     many systems use smaller values (4.3BSD uses 30, 4.2BSD used 15).

     The maximum possible value of this field is 255, and most UNIX systems set the TTL field of
     ICMP ECHO_REQUEST packets to 255.	This is why you will find you can ``ping'' some hosts,
     but not reach them with telnet(1) or ftp(1).

     In normal operation ping prints the ttl value from the packet it receives.  When a remote
     system receives a ping packet, it can do one of three things with the TTL field in its
     response:

     o	 Not change it; this is what Berkeley UNIX systems did before the 4.3BSD-Tahoe release.
	 In this case the TTL value in the received packet will be 255 minus the number of
	 routers in the round-trip path.

     o	 Set it to 255; this is what current Berkeley UNIX systems do.	In this case the TTL
	 value in the received packet will be 255 minus the number of routers in the path from
	 the remote system to the pinging host.

     o	 Set it to some other value.  Some machines use the same value for ICMP packets that they
	 use for TCP packets, for example either 30 or 60.  Others may use completely wild val-
	 ues.

EXIT STATUS
     ping returns 0 on success (the host is alive), and non-zero if the arguments are incorrect
     or the host is not responding.

SEE ALSO
     netstat(1), icmp(4), inet(4), ip(4), ifconfig(8), routed(8), spray(8), traceroute(8)

HISTORY
     The ping command appeared in 4.3BSD.  IPsec support was added by WIDE/KAME project.

BUGS
     Flood pinging is not recommended in general, and flood pinging a broadcast or multicast
     address should only be done under very controlled conditions.

     The ping program has evolved differently under different operating systems, and in some
     cases the same flag performs a different function under different operating systems.  The -t
     flag conflicts with FreeBSD.  The -a, -c, -I, -i, -l, -P, -p, -s, and -t flags conflict with
     Solaris.

     Some hosts and gateways ignore the RECORD_ROUTE option.

     The maximum IP header length is too small for options like RECORD_ROUTE to be completely
     useful.  There's not much that that can be done about this, however.

BSD					September 10, 2011				      BSD
Unix & Linux Commands & Man Pages : ©2000 - 2018 Unix and Linux Forums


All times are GMT -4. The time now is 06:00 PM.