Login or Register to Ask a Question and Join Our Community

Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

pciide(4) [netbsd man page]

PCIIDE(4)						   BSD Kernel Interfaces Manual 						 PCIIDE(4)

NAME

     pciide -- PCI IDE disk controllers driver

SYNOPSIS

     pciide* at pci? dev ? function ? flags 0x0000
     pciide* at pnpbios? index ?

DESCRIPTION

     The pciide driver supports the PCI IDE controllers as specified in the "PCI IDE controller specification, revision 1.0" draft, and provides
     the interface with the hardware for the ata driver.  Please use the chip-specific drivers for the following controllers for enhanced and DMA
     support:
	   -   Acard ATP850 (Ultra/33) and ATP860 (Ultra/66) IDE Controllers: acardide(4)
	   -   Acer labs M5229 IDE Controller: aceride(4)
	   -   Advanced Micro Devices AMD-756, 766, and 768 IDE Controllers: viaide(4)
	   -   Advanced Micro Devices Geode IDE Controllers: geodeide(4)
	   -   CMD Tech PCI0643, PCI0646, PCI0648, and PCI0649 IDE Controllers: cmdide(4)
	   -   Contaq Microsystems/Cypress CY82C693 IDE Controller: cypide(4)
	   -   HighPoint HPT366 Ultra/66, HPT370 Ultra/100, HPT372, and HPT374 Ultra/133 IDE controller: hptide(4)
	   -   Intel PIIX, PIIX3, and PIIX4 IDE Controllers: piixide(4)
	   -   Intel i31244 Serial ATA controller: artsata(4)
	   -   Intel 82801 (ICH/ICH0/ICH2/ICH3/ICH4/ICH5/ICH6) IDE Controllers: piixide(4)
	   -   Intel SCH IDE Controllers: schide(4)
	   -   NVIDIA nForce/nForce2 IDE Controllers: viaide(4)
	   -   OPTi 82c621 (plus a few of its derivatives) IDE Controllers: optiide(4)
	   -   Promise PDC20246 (Ultra/33), PDC20262 (Ultra/66), PDC20265/PDC20267 (Ultra100), PDC20268 (Ultra/100TX2 and Ultra/100TX2v2),
	       Ultra/133, Ultra/133TX2 and Ultra/133TX2v2 PCI IDE controllers: pdcide(4)
	   -   Serverworks K2 SATA controllers: svwsata(4)
	   -   Silicon Image 0680 IDE controller: cmdide(4)
	   -   Silicon Image SATALink 3112 Serial ATA controller: satalink(4)
	   -   Silicon Image SteelVine 3124/3132/3531 Serial ATA II controller: siisata(4)
	   -   Silicon Integrated System 5597/5598 IDE controller: siside(4)
	   -   Symphony Labs 82C105 and Winbond W83C553F IDE controller: slide(4)
	   -   VIA Technologies VT82C586, VT82C586A, VT82C596A, VT82C686A, VT8233A, and VT8235 IDE Controllers: viaide(4)

     The 0x0001 flag forces the pciide driver to use DMA when there is no explicit DMA mode setting support for the controller but DMA is present.
     If the BIOS didn't set up the controller properly, this can cause a machine hang.

     The 0x0002 flag forces the pciide driver to disable DMA on chipsets for which DMA would normally be enabled.  This can be used as a debugging
     aid, or to work around problems where the IDE controller is wired up to the system incorrectly.

SEE ALSO

     acardide(4), aceride(4), artsata(4), ata(4), atapi(4), cmdide(4), cypide(4), geodeide(4), hptide(4), intro(4), optiide(4), pci(4), pdcide(4),
     piixide(4), pnpbios(4), satalink(4), schide(4), siisata(4), siside(4), slide(4), viaide(4), wd(4), wdc(4)

BSD
								 November 7, 2010							       BSD

Check Out this Related Man Page

HD(4)							     Linux Programmer's Manual							     HD(4)

NAME

       hd - MFM/IDE hard disk devices

DESCRIPTION

       The  hd*  devices  are block devices to access MFM/IDE hard disk drives in raw mode.  The master drive on the primary IDE controller (major
       device number 3) is hda; the slave drive is hdb.  The master drive of the second controller (major device number 22) is hdc and	the  slave
       hdd.

       General	IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
       partition on that physical drive.  The first form, hdX, is used to address the whole drive.  Partition numbers are assigned  in	the  order
       the  partitions	are  discovered,  and only nonempty, nonextended partitions get a number.  However, partition numbers 1-4 are given to the
       four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended.  Thus, the first  logi-
       cal  partition  will be hdX5.  Both DOS-type partitioning and BSD-disklabel partitioning are supported.	You can have at most 63 partitions
       on an IDE disk.

       For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on  the
       second one.

       They are typically created by:

	      mknod -m 660 /dev/hda b 3 0
	      mknod -m 660 /dev/hda1 b 3 1
	      mknod -m 660 /dev/hda2 b 3 2
	      ...
	      mknod -m 660 /dev/hda8 b 3 8
	      mknod -m 660 /dev/hdb b 3 64
	      mknod -m 660 /dev/hdb1 b 3 65
	      mknod -m 660 /dev/hdb2 b 3 66
	      ...
	      mknod -m 660 /dev/hdb8 b 3 72
	      chown root:disk /dev/hd*

FILES

       /dev/hd*

SEE ALSO

       chown(1), mknod(1), sd(4), mount(8)

COLOPHON

       This  page is part of release 3.27 of the Linux man-pages project.  A description of the project, and information about reporting bugs, can
       be found at http://www.kernel.org/doc/man-pages/.

Linux								    1992-12-17								     HD(4)
Man Page