10 More Discussions You Might Find Interesting
1. AIX
Hi Folks,
I am facing an issue with the performance.
P4 with 1 processor and 16 GB RAM and SAN HDD = Oracle report takes 25 minutes
P5 with 2 processors and 16 GB RAM internall HDD with LPAR = Oracle Report takes 1 hour 15 minutes ( please note I have assigned all the max processors and... (7 Replies)
Discussion started by: filosophizer
7 Replies
2. UNIX for Dummies Questions & Answers
i just got a copy of windows and when i go to install it, it says i cant because it needs an ntfs file system. can anyone help me format my hard drive through linux? (2 Replies)
Discussion started by: camroc84
2 Replies
3. UNIX for Dummies Questions & Answers
I have a Sun Blade 1500 (sparc)
I have two HDD's both configured with Solaris 10.
How do I chose at boot which HDD I want to use?
I've had a look through the FAQ, also done a web search but haven't come up with requisite info.
touch /reconfigure does not seem to help.
Any suggestions... (8 Replies)
Discussion started by: lewtargett
8 Replies
4. UNIX for Dummies Questions & Answers
Over the last few months the HDD spins louder and louder, so I fiqured its time to replace the HDD. Its been running 24/7/365 since 98 :eek:. yes i said since 98 :D
I have an IBM system 43P Model 240. 233 MHz. running AIX Version 4.
The current HDD is an IBM DGHS COMP IEC -950
FRU PN#... (5 Replies)
Discussion started by: Chevy89rocks
5 Replies
5. Solaris
hello gurus,
i have just installed the os on hdd,
when i write down boot command on ok prompt,
I get following error continuously.
what could be the possible problem
WARNING: /ssm@0,0/pci@18,600000/scsi@2/sd@0,0 (sd0):
auto request sense failed (reason=reset)
WARNING:... (2 Replies)
Discussion started by: sameergrover
2 Replies
6. UNIX for Dummies Questions & Answers
I have seagate USB 2.0 HDD which was working good on my windows system
Recently I have started using red hat Linux 2.6.9-55.0.12.EL (i686 i686 i386 GNU/Linux)
The USB is not at all detected in Linux even if I reboot with it attached to the PC. The same can be detected on any Windows system.
... (0 Replies)
Discussion started by: mahendrakamath
0 Replies
7. Solaris
Hi theres
I am quite new to solaris, I have 40GB HDD in which I have created only 10 GB partition & installed solaris 10. Now I want to add another 10GB from remaining 30GB space. I tried this with format utility but I get stuck after I create fdsik partition. After creating this I cant... (1 Reply)
Discussion started by: i_mroy
1 Replies
8. Solaris
I have another Hdd problem with Ultra 1 machine
the hdd is segate (+-)17560 MB and when I start installtion of sun solaries 2.6 the system sees the hdd correctly, and the installtion goes fine with partioning the disk as follows
/ 150 MB
swap 500 MB
/user 1000 MB
/user1 100MB
/usr3 5500 MB... (4 Replies)
Discussion started by: adol3
4 Replies
9. Ubuntu
Umm How can I get the Knoppix can be booted off my hard drive instead of the CD. I dont like using the CD. :confused: (4 Replies)
Discussion started by: shade11
4 Replies
10. Shell Programming and Scripting
Hi Engg. ! :mad:
I have a harddisk on which SCO UNIX Open Server was installed. There was some data (in .dbf format) on it. Present condition of HDD is that it is not booting. Now I want to mount this HDD through other HDD on which SCO UNIX Open Server is installed by attaching... (0 Replies)
Discussion started by: Niraj Gopal Sha
0 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
chown(1), mknod(1), sd(4), mount(8)
COLOPHON
This page is part of release 3.25 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)