9 More Discussions You Might Find Interesting
1. Linux
Dear experts
I've managed to configure Blind, Zone files and i can view the domain that i created via nslookup and ping the domain on the same server.
Server: 41.216.x.xx
Address: 41.216.4.175#53
Name: mail.eeee.co.zm
Address: 41.216.x.xx
However, when... (1 Reply)
Discussion started by: herberwz
1 Replies
2. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
3. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
4. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
5. AIX
dears is the configurations in the red correct for sendmail.cf
DWdatawarehouse
my louts nots server = DSlstn-lono-svr
# ... define this only if sendmail cannot automatically determine your domain
#Dj$w.Foo.COM
# top level psuedo domains
CP.
# UUCP relay host
#DYrelayhostname... (4 Replies)
Discussion started by: thecobra151
4 Replies
6. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
7. UNIX for Advanced & Expert Users
Hi,
I am using Enterprise Linux Server release 5.2, now i am configuring Samba server, i want to access linux directories from Windows xp/2003 desktops. I installed and configured but i am unable to access them, could you please give me suggestion about configurations.
Thanks. (2 Replies)
Discussion started by: marmam
2 Replies
8. Solaris
Hello All,
I was finaly was able to recover my root password, thanks to this board ;)
Now, I need to change the IP, well when I do netstat -rn the following displays:
192.168.0.77 127.0.0.1 UH 1 0 lo0
127.0.2.1 127.0.0.1 UH 1... (3 Replies)
Discussion started by: nexOne
3 Replies
9. IP Networking
Hi all....
I’ll have a test for the IT department in the company I work, the test is about UNIX administration and TCP/IP routing configuration, in the UNIX admin server I don’t have any problem, but routing is my pain.
To make it more difficult, I can not use companies infrastructure to... (1 Reply)
Discussion started by: TARFU
1 Replies
MVSATA(4) BSD Kernel Interfaces Manual MVSATA(4)
NAME
mvsata -- Marvell Hercules-I and Hercules-II SATA controllers driver
SYNOPSIS
mvsata* at pci? dev ? function ?
DESCRIPTION
The mvsata driver supports the Marvell Hercules-I and Hercules-II family of SATA controllers, interfacing the hardware with the ata(4) and
atapi(4) subsystems.
The following controllers are supported by the mvsata driver:
Adaptec RAID 1420SA
Adaptec RAID 1430SA
Marvell 88SX50xx Hercules-I
Marvell 88SX60xx Hercules-II
Marvell 88SX70xx Hercules-II
Triones Technologies RocketRAID 2310 RAID card
The 88SX60xx and later support Native Command Queuing. The 88SX70xx also supports ATAPI.
SEE ALSO
ata(4), atapi(4), pci(4), wd(4)
HISTORY
The mvsata driver first appeared in NetBSD 6.0.
AUTHORS
The mvsata driver was written by KIYOHARA Takashi <kiyohara@kk.iij4u.or.jp>.
BUGS
SATA Native Command Queuing is not yet supported.
Device hot swapping is not yet supported.
ATAPI is not yet tested.
Marvell's Software RAID is not yet supported by the
ataraid(4) driver. raid(4) can be used instead.
BSD
July 19, 2009 BSD