02-04-2006
10 More Discussions You Might Find Interesting
1. IP Networking
How do I configure TCP/IP on an old SCO UNIX 3.2 v4.0
I can't seem to find any type of documentation on it.
Can someone give me step by step info or refer some type of article? (11 Replies)
Discussion started by: gguzman
11 Replies
2. IP Networking
Hello,
I have 4 unix (Solaris 8) stations need to setup on network.
what is a easy way and quick to setup TCP/IP so I can bring it online?. Please advise! (3 Replies)
Discussion started by: phapvn
3 Replies
3. UNIX for Dummies Questions & Answers
Can anybody help me on how to configure the network in Sun Solaris. This is my first time to touch sun system please help!!!:confused: :confused: (2 Replies)
Discussion started by: jameswong
2 Replies
4. Solaris
Hello,
I want to change the IP of my SUN solaris machine but i am not bale to find the right way. I tried the following steps:
1) edit /etc/inet/hosts and change IP address for host listed in
/etc/hostname.le0
2) ifconfig le0 down
3) ifconfig le0 inet NEW_IP_ADDR netmask + broadcast + ... (5 Replies)
Discussion started by: er_aparna
5 Replies
5. UNIX for Dummies Questions & Answers
Hi,
I am working in sun solaris server.I have Kyocera FS-1030D KX printer in my network .I have configured this printer for windows.I want to configure same printer to sun solaris.Is this possible.Give me some ideas. (2 Replies)
Discussion started by: arulkumar
2 Replies
6. Solaris
Hi Experts,
I am new for solaris, i am using Solaris10,can you anyone assist me how to configure IP in my machine.
Thanks (4 Replies)
Discussion started by: daya.pandit
4 Replies
7. Solaris
Dear All,
I am a beginner of Sun Solaris. Now I install Sun Solaris 10 on my machine Brand Dell optiplex 745. When i complete installation I found no Network Card
in my computer by using command ifconfig -a, I found only loopback Adapter.
Could anyone help me to solve this problem?
Cheer,
... (5 Replies)
Discussion started by: veasnabee
5 Replies
8. Solaris
Hi everyone,
Normally it always easier in Sparc machine, i can set or manually use the boot-device in NVram to boot the mirrored disk. However I have a big trouble about x86 mirror for a long time. I have been doing anything i can: search document, google, ask the others.
Recently i did as... (5 Replies)
Discussion started by: tien86
5 Replies
9. Solaris
Hi everyone.
Im new to Sun Solaris or the Unix environment. My only background is the DOS command in windows and a little bit of c++ programming. I always worked with troubleshooting hardware and software issues with windows.
Now that I need to configure tape drives using sun solaris, I had... (11 Replies)
Discussion started by: graboid888
11 Replies
10. Solaris
Is it possible to install 2 flavors of Unix on a single machine ?
-HP Unix
-SUN Solaris
Please provide sufficient information to carry both of the above OS installation on single machine.Any guide/steps/document will do. (3 Replies)
Discussion started by: mahix
3 Replies
ndd(1M) System Administration Commands ndd(1M)
NAME
ndd - get and set driver configuration parameters
SYNOPSIS
ndd [-set] driver parameter [value]
DESCRIPTION
ndd gets and sets selected configuration parameters in some kernel drivers. Currently, ndd only supports the drivers that implement the
TCP/IP Internet protocol family. Each driver chooses which parameters to make visible using ndd. Since these parameters are usually
tightly coupled to the implementation, they are likely to change from release to release. Some parameters may be read-only.
If the -set option is omitted, ndd queries the named driver, retrieves the value associated with the specified parameter, and prints it. If
the -set option is given, ndd passes value, which must be specified, down to the named driver which assigns it to the named parameter.
By convention, drivers that support ndd also support a special read-only parameter named ``?'' which can be used to list the parameters
supported by the driver.
EXAMPLES
Example 1: Getting Parameters Supported By The TCP Driver
To see which parameters are supported by the TCP driver, use the following command:
example% ndd /dev/tcp ?
The parameter name ``?'' may need to be escaped with a backslash to prevent its being interpreted as a shell meta character.
The following command sets the value of the parameter ip_forwarding in the dual stack IP driver to zero. This disables IPv4 packet forward-
ing.
example% ndd -set /dev/ip ip_forwarding 0
Similarly, in order to disable IPv6 packet forwarding, the value of parameter ip6_forwarding
example% ndd -set /dev/ip ip6_forwarding 0
To view the current IPv4 forwarding table, use the following command:
example% ndd /dev/ip ipv4_ire_status
To view the current IPv6 forwarding table, use the following command:
example% ndd /dev/ip ipv6_ire_status
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
nca(1), ioctl(2), attributes(5), arp(7P), ip(7P), ip6(7P), tcp(7P), udp(7P)
NOTES
The parameters supported by each driver may change from release to release. Like programs that read /dev/kmem, user programs or shell
scripts that execute ndd should be prepared for parameter names to change.
The ioctl() command that ndd uses to communicate with drivers is likely to change in a future release. User programs should avoid making
dependencies on it.
The meanings of many ndd parameters make sense only if you understand how the driver is implemented.
SunOS 5.10 8 Nov 1999 ndd(1M)