Sponsored Content
Full Discussion: Modem
Top Forums UNIX for Advanced & Expert Users Modem Post 9674 by LivinFree on Thursday 1st of November 2001 03:02:58 AM
Old 11-01-2001
If you can, do a tail -f /var/log/messages while the modem is dialing. If not, at least examine this file afterwards for more info on what's happening. If you still can't figure it out, post the bottom part of the file (with the usefull info), and we can try to help.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Modem on HP-UX 10.20

Hi everyone I am having some real difficulties getting a dial in modem to work on one of my HP boxes. It's a mux modem on port 7 which I have set up at 9600 baud. I can dial in, the handshakes are completed, but then it returns incoherent characters on the emulation screen. I think my dial in... (1 Reply)
Discussion started by: alwayslearningunix
1 Replies

2. UNIX for Dummies Questions & Answers

Modem problem: "Sorry, modem is busy"

Hi! I have a little prob with dialing up to the internet... When I try connect, it says "Sorry, modem is busy"... Specs: Laptop 56K modem Slackware 8.0 Kernel 2.4.5 Cheers;) (4 Replies)
Discussion started by: satan404
4 Replies

3. UNIX for Dummies Questions & Answers

Modem Volume

Specs: Dlink DFE-560EL external modem. RedHat 7.1 How do you turn off the modem volume? I am getting annoyed of it beeping everytime I use it but there is no switch on the hardware to tune down the volume. I have tried using minicom and use the following commands: ATL0 ATM0 Next, I... (2 Replies)
Discussion started by: arz
2 Replies

4. UNIX for Dummies Questions & Answers

Modem

Pleaseee... Helpppp.... !!! I am using SCO Open Server 5.05. Recently, i have upgraded the system which means transfer all apps and data to the new system. Everything work well except one thing. On my old system i have an external modem which to dial out. Now that i use the same modem on... (4 Replies)
Discussion started by: jackpotp
4 Replies

5. UNIX for Dummies Questions & Answers

modem

I have got Suse 8.0 by using a modem (US Robotics 56K Faxmodem Ext). During connection i got the error 16. I tried it under RedHat and Mandrake too.....same problem. What can i do ? Thanx...a lot... Logfile: SuSE Meta pppd (smpppd), Version 0.73 on zuhause. wwwoffle not is running ... (1 Reply)
Discussion started by: Pennywize
1 Replies

6. UNIX for Dummies Questions & Answers

Modem - Test /dev/modem

Ok. I tried following the directions from some of the other threads, but I've hit a road block. I have red hat 7.3 and I installed the hcf package: hcfpcimodem-0.99lnxtbeta03042700k2.4.18_3-1rh.i386.rpm It installed ok, no errors, but I still can't get linux to find my modem. I've tried... (2 Replies)
Discussion started by: lawadm1
2 Replies

7. UNIX for Dummies Questions & Answers

Dial-Up Modem

Im using Kinternet with a Lucent modem on Suse 9.0 Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0 This is the log that Kinternet gives after trying to connect: SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux. Status... (0 Replies)
Discussion started by: Synbios
0 Replies

8. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks (2 Replies)
Discussion started by: waterbear
2 Replies

9. Solaris

Modem

hi folks, i am looking for a analog modem to use it with a solaris9 sparc mashine. as far as i know, solaris communicates with the modem using AT-commands. so do i need a special modem for solaris or just a modem? i am open for everything. PCI-modem, seriell modem, usb modem. what are you using? i... (1 Reply)
Discussion started by: pressy
1 Replies

10. IP Networking

modem detection

How to get information that where is my modem configured in /dev. I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Discussion started by: s123.radha
0 Replies
Gtk2::RecentInfo(3)					User Contributed Perl Documentation				       Gtk2::RecentInfo(3)

NAME
Gtk2::RecentInfo HIERARCHY
Glib::Boxed +----Gtk2::RecentInfo METHODS
timestamp = $info->get_added; timestamp = $info->get_modified; timestamp = $info->get_visited; cut integer = $info->get_age (exec, count, timestamp) = $info->get_application_info ($app_name) o $app_name (string) (applications) = $info->get_applications string = $info->get_description string = $info->get_display_name boolean = $info->exists (groups) = $info->get_groups boolean = $info->has_application ($app_name) o $app_name (string) boolean = $info->has_group ($group_name) o $group_name (string) pixbuf = $info->get_icon ($size) o $size (integer) boolean = $info->is_local string = $info->last_application boolean = $info->match ($other_info) o $other_info (Gtk2::RecentInfo) string = $info->get_mime_type unix timestamp = $info->get_modified boolean = $info->get_private_hint string = $info->get_short_name string = $info->get_uri_display string = $info->get_uri unix timestamp = $info->get_visited SEE ALSO
Gtk2, Glib::Boxed COPYRIGHT
Copyright (C) 2003-2008 by the gtk2-perl team. This software is licensed under the LGPL. See Gtk2 for a full notice. perl v5.12.1 2010-07-05 Gtk2::RecentInfo(3)
All times are GMT -4. The time now is 05:40 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy