10-25-2001
unix and the cable modem
If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that supports unix and if so are all the cable modem the same and will work with any cable company?
thank you for your help!!
10 More Discussions You Might Find Interesting
1. IP Networking
It was easy in mandrake, but i don't know how in red hat. I have an Allied Telesyn AT2400/ET
If it's possible in mandrake then i know it's possible in red hat. (5 Replies)
Discussion started by: walrus
5 Replies
2. UNIX for Dummies Questions & Answers
I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now? (4 Replies)
Discussion started by: zorro
4 Replies
3. UNIX for Dummies Questions & Answers
Caldera eDesktop 2.4 - Cable Modem
my NIC card has been detected, but funny scenario:
#dmesg
eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef
/*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module.... (1 Reply)
Discussion started by: zorro
1 Replies
4. UNIX for Dummies Questions & Answers
Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how.
Thank you for all your help. (5 Replies)
Discussion started by: gparsons70
5 Replies
5. IP Networking
I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how... (3 Replies)
Discussion started by: ftn96
3 Replies
6. UNIX for Dummies Questions & Answers
hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem ,
i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies
7. UNIX for Dummies Questions & Answers
I have a XP computer which is my primary. I recently, well just today installed a old version of Mandrake Linux 6.5 I had laying on a self collecting dust on a old PII 233mhz that had to be vacummed out before I could use it.
I have my XP computer connected by 10/100 NIC to a cable modem. My... (1 Reply)
Discussion started by: garfunkle
1 Replies
8. BSD
hi
I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system.
When I type, I get
# ifconfig -a
lo0 : ....
...
...
rl0 : ....
...
...
vr0 : ...
...
...
I have two network cards (the machine will be a router).
I created... (1 Reply)
Discussion started by: fnoyan
1 Replies
9. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
10. OS X (Apple)
Hi.
I have a very strange problem, so strange I don't even know which sub-forum to post it to.
Last week, my cable modem broke, so I took it back and got a new one.
The new one doesn't work with my old router so, for now, I have to connect the modem directly to my Mac with an ethernet... (14 Replies)
Discussion started by: Scott
14 Replies
LEARN ABOUT OPENSOLARIS
scconf_transp_adap_ge
scconf_transp_adap_ge(1M) System Administration Commands scconf_transp_adap_ge(1M)
NAME
scconf_transp_adap_ge - configure the Gigabit Ethernet (ge) transport adapter
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
You can configure ge adapters as cluster transport adapters. These adapters can only be used with transport type dlpi.
The ge adapter connects to a transport switch or to another ge adapter on a different node. In either case, the connection is made through
a transport cable.
When a transport switch is used and the endpoints of the transport cable are configured using scconf, scinstall, or other tools, you are
asked to specify a port name on the transport switch. You can provide any port name, or accept the default, as long as the name is unique
for the switch.
The default is to set the port name to the node ID hosting the adapter at the other end of the cable.
There are no user configurable properties for cluster transport adapters of this type.
SEE ALSO
clinterconnect(1CL), clnode(1CL), scconf(1M), scinstall(1M), ge(7D)
Sun Cluster 3.2 4 May 2006 scconf_transp_adap_ge(1M)