10-31-2005
Thanks Jai, there is the asked information
C:3.91GB NTFS
3.42GB ext3
682MB (swap)
D:29.27GB NTFS
for boot loader I am using GNU GRUB v. 0.95
an the kernel is the 2.6.12 version
I do not know if this information is what you need.
Thanks for your help.
Regards
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
i have windows 2000 on hda. when i was running freebsd on hdb, i installed their boot manager and it worked fine.
today i installed suse linux on hdb in place of freebsd, but the freebsd boot manager is still there. it will boot windows but has some problems trying to boot linux. the boot... (1 Reply)
Discussion started by: nydel
1 Replies
2. UNIX for Dummies Questions & Answers
Hi Everyone,
I have a problem. I'm trying too reinstall sun solaris 8.0 on may Sunfire 280r but solaris 9.0 is all ready installed. I tried to boot from cd rom it keeps telling me that File does not seem executable. I need to get Solaris 8.0 on this system. I have boot all ready in single mode... (4 Replies)
Discussion started by: Peterh
4 Replies
3. UNIX for Dummies Questions & Answers
During the boot process of my SPARCstation 5, it hangs up at this message: Setting default interface for multicast: add net 224.0.0.0: gateway jpt2. What do I need to do to get past this point? Is there something I need to turn off? (2 Replies)
Discussion started by: saucierm
2 Replies
4. UNIX for Dummies Questions & Answers
Hi!
I got some serious problems with booting the computer. When started it prints GRUB GRUB GRUB all over the screen. tchan on #grub tried to help me but with no result. Here is the log.
Mabey there is something that we have missed?:confused: (3 Replies)
Discussion started by: Barfly.se
3 Replies
5. Filesystems, Disks and Memory
i have 2 server es40 and ds20 with with unix truevector , the es40 is down cause of hard problem
i have traied to take hard disksfrom ES40 and put then in DS20
but there is problem
-------------------------------------------------------------------------------------------------------------... (1 Reply)
Discussion started by: lastfreemen
1 Replies
6. Solaris
I'm new to Unix so please bear with me.
We had a Ultra 10 running solaris 8 and the motherboard went. So we bought a replacement Ultra 10 on ebay. Exact same hardware. Swapped out the drives with our drives and booted. The new system was set up to boot off disk1 and ours were set to boot off... (1 Reply)
Discussion started by: jbestor
1 Replies
7. AIX
I am trying to install AIX 4.3 on a 44P-170 and am having problems. I have the 44P connected to a laptop through the serial port and am trying to boot from the IBM AIX 4.3 CD and I can only get as far as the SMS (I believe) screen. The current Processor Firmware is sh040616 and the system... (3 Replies)
Discussion started by: SeanU
3 Replies
8. Solaris
Can't seem to get it to boot from cd
boot cd
rebooting with command: boot cd
boot device: /pci@8600000/sunw,qlc@4/fp@0,0/disk@1,0 file and args: cd
boot: cannot open cd
enter filename :
trying to install solaris 9 9/04 just to use it as a simple workstation on home network quite new... (25 Replies)
Discussion started by: solnewbie
25 Replies
9. Solaris
Hi folks, I was trying to setup Network based NFS installation with PXE.
I'm using virtual box for this purpose. I have one redhat (DHCP) server and Solaris 10 (Install server - Source) and on the other one am trying to install solaris using PXE. As in, dhcp address and boot file can be fetched... (2 Replies)
Discussion started by: vijaytrendz
2 Replies
10. Solaris
Hi all,
I've just replaced the eprom battery on my Sun Ultra-30 and having boot issues. For some reason its trying to boot off the network instead of the DISK1. Howe can I change it so the open boot does not default to the boot device: NET
Thanks,
Rob (3 Replies)
Discussion started by: robbo007
3 Replies
BOOTCTL(1) bootctl BOOTCTL(1)
NAME
bootctl - Control the firmware and boot manager settings
SYNOPSIS
bootctl [OPTIONS...] status
bootctl [OPTIONS...] list
bootctl [OPTIONS...] update
bootctl [OPTIONS...] install
bootctl [OPTIONS...] remove
DESCRIPTION
bootctl checks, updates, installs or removes the boot loader from the current system.
bootctl status checks and prints the currently installed versions of the boot loader binaries and all current EFI boot variables.
bootctl list displays all configured boot loader entries.
bootctl update updates all installed versions of systemd-boot, if the current version is newer than the version installed in the EFI system
partition. This also includes the EFI default/fallback loader at /EFI/BOOT/BOOT*.EFI. A systemd-boot entry in the EFI boot variables is
created if there is no current entry. The created entry will be added to the end of the boot order list.
bootctl install installs systemd-boot into the EFI system partition. A copy of systemd-boot will be stored as the EFI default/fallback
loader at /EFI/BOOT/BOOT*.EFI. A systemd-boot entry in the EFI boot variables is created and added to the top of the boot order list.
bootctl remove removes all installed versions of systemd-boot from the EFI system partition, and removes systemd-boot from the EFI boot
variables.
If no command is passed, status is implied.
OPTIONS
The following options are understood:
-h, --help
Print a short help text and exit.
--version
Print a short version string and exit.
--path=
Path to the EFI System Partition (ESP). If not specified, /efi, /boot, and /boot/efi are checked in turn. It is recommended to mount
the ESP to /boot, if possible.
-p, --print-path
This option modifies the behaviour of status. Just print the path to the EFI System Partition (ESP) to standard output and exit.
--no-variables
Do not touch the EFI boot variables.
EXIT STATUS
On success, 0 is returned, a non-zero failure code otherwise.
SEE ALSO
Boot loader specification[1] systemd boot loader interface[2]
NOTES
1. Boot loader specification
https://www.freedesktop.org/wiki/Specifications/BootLoaderSpec
2. systemd boot loader interface
https://www.freedesktop.org/wiki/Software/systemd/BootLoaderInterface
systemd 237 BOOTCTL(1)