|
|
Sponsored Content
Operating Systems
Linux
Debian
Problems with boot
Post 88042 by GEIER on Monday 31st of October 2005 10:19:28 AM
10-31-2005
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
i have windows 2000 on hda. when i was running freebsd on hdb, i installed their boot manager and it worked fine.
today i installed suse linux on hdb in place of freebsd, but the freebsd boot manager is still there. it will boot windows but has some problems trying to boot linux. the boot... (1 Reply)
Discussion started by: nydel
1 Replies
2. UNIX for Dummies Questions & Answers
Hi Everyone,
I have a problem. I'm trying too reinstall sun solaris 8.0 on may Sunfire 280r but solaris 9.0 is all ready installed. I tried to boot from cd rom it keeps telling me that File does not seem executable. I need to get Solaris 8.0 on this system. I have boot all ready in single mode... (4 Replies)
Discussion started by: Peterh
4 Replies
3. UNIX for Dummies Questions & Answers
During the boot process of my SPARCstation 5, it hangs up at this message: Setting default interface for multicast: add net 224.0.0.0: gateway jpt2. What do I need to do to get past this point? Is there something I need to turn off? (2 Replies)
Discussion started by: saucierm
2 Replies
4. UNIX for Dummies Questions & Answers
Hi!
I got some serious problems with booting the computer. When started it prints GRUB GRUB GRUB all over the screen. tchan on #grub tried to help me but with no result. Here is the log.
Mabey there is something that we have missed?:confused: (3 Replies)
Discussion started by: Barfly.se
3 Replies
5. Filesystems, Disks and Memory
i have 2 server es40 and ds20 with with unix truevector , the es40 is down cause of hard problem
i have traied to take hard disksfrom ES40 and put then in DS20
but there is problem
-------------------------------------------------------------------------------------------------------------... (1 Reply)
Discussion started by: lastfreemen
1 Replies
6. Solaris
I'm new to Unix so please bear with me.
We had a Ultra 10 running solaris 8 and the motherboard went. So we bought a replacement Ultra 10 on ebay. Exact same hardware. Swapped out the drives with our drives and booted. The new system was set up to boot off disk1 and ours were set to boot off... (1 Reply)
Discussion started by: jbestor
1 Replies
7. AIX
I am trying to install AIX 4.3 on a 44P-170 and am having problems. I have the 44P connected to a laptop through the serial port and am trying to boot from the IBM AIX 4.3 CD and I can only get as far as the SMS (I believe) screen. The current Processor Firmware is sh040616 and the system... (3 Replies)
Discussion started by: SeanU
3 Replies
8. Solaris
Can't seem to get it to boot from cd
boot cd
rebooting with command: boot cd
boot device: /pci@8600000/sunw,qlc@4/fp@0,0/disk@1,0 file and args: cd
boot: cannot open cd
enter filename :
trying to install solaris 9 9/04 just to use it as a simple workstation on home network quite new... (25 Replies)
Discussion started by: solnewbie
25 Replies
9. Solaris
Hi folks, I was trying to setup Network based NFS installation with PXE.
I'm using virtual box for this purpose. I have one redhat (DHCP) server and Solaris 10 (Install server - Source) and on the other one am trying to install solaris using PXE. As in, dhcp address and boot file can be fetched... (2 Replies)
Discussion started by: vijaytrendz
2 Replies
10. Solaris
Hi all,
I've just replaced the eprom battery on my Sun Ultra-30 and having boot issues. For some reason its trying to boot off the network instead of the DISK1. Howe can I change it so the open boot does not default to the boot device: NET
Thanks,
Rob (3 Replies)
Discussion started by: robbo007
3 Replies
LEARN ABOUT DEBIAN
ntfs-3g.probe
NTFS-3G.PROBE(8) System Manager's Manual NTFS-3G.PROBE(8) NAME
ntfs-3g.probe - Probe an NTFS volume mountability SYNOPSIS
ntfs-3g.probe <--readonly|--readwrite> volume DESCRIPTION
The ntfs-3g.probe utility tests a volume if it's NTFS mountable read-only or read-write, and exits with a status value accordingly. The volume can be a block device or image file. OPTIONS
Below is a summary of the options that ntfs-3g.probe accepts. -r, --readonly Test if the volume can be mounted read-only. -w, --readwrite Test if the volume can be mounted read-write. -h, --help Display help and exit. EXAMPLE
Test if /dev/sda1 can be mounted read-write: ntfs-3g.probe --readwrite /dev/sda1 EXIT CODES
The exit codes are as follows: 0 Volume is mountable. 11 Syntax error, command line parsing failed. 12 The volume doesn't have a valid NTFS. 13 Inconsistent NTFS, hardware or device driver fault, or unsetup SoftRAID/FakeRAID hardware. 14 The NTFS partition is hibernated. 15 The volume was not cleanly unmounted. 16 The volume is already exclusively opened and in use by a kernel driver or software. 17 Unsetup SoftRAID/FakeRAID hardware. 18 Unknown reason. 19 Not enough privilege to mount. 20 Out of memory. 21 Unclassified FUSE error. KNOWN ISSUES
Please see http://tuxera.com/community/ntfs-3g-faq/ for common questions and known issues. If you think you have found an undocumented problem in the latest release of the software then please send an email describing it in detail. You can contact the development team on the ntfs-3g-devel@lists.sf.net address. AUTHORS
ntfs-3g.probe was written by Szabolcs Szakacsits. THANKS
Alon Bar-Lev has integrated the utility into the NTFS-3G build process and tested it with Erik Larsson before the public release. SEE ALSO
ntfs-3g(8) ntfs-3g.probe 2012.1.15AR.5 January 2008 NTFS-3G.PROBE(8)