09-26-2001
Imaging...systemimager.org
After I do my fresh installs I take a snapshot of them using systemimager . It works like a charm. No dd required.
Your system must support rsync for this option to work,...and if you're live on the internet, then maybe you may want to review your security concerns regarding having this daemon working on your server.
http://www.systemimager.org
Good Luck. Hope this helps.
VJ
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Does anyone know of any good imaging tools that can be used to create an image of a Sco-Unix box? (2 Replies)
Discussion started by: gmrfh1
2 Replies
2. UNIX for Advanced & Expert Users
Dears,
I have server has two port's(Enet0,Enet1) what I want as follows:
Make the two port's has same IP address
where, if the port Enet0 became down automaticly Enet1 become up :confused: .
Amen (4 Replies)
Discussion started by: amen00
4 Replies
3. UNIX for Advanced & Expert Users
Here we want to implement the network redundancy on UNIX with the software.
The two network interface cards are configured on the UNIX node,once one card is down or unnormal,the other can take over. Those aplications that used the tcp ,udp,multicast protocol can also been switched at the same... (2 Replies)
Discussion started by: Frank2004
2 Replies
4. UNIX for Dummies Questions & Answers
We have had some email outages in the last few months and my boss is asking is it worth going with one of those email redundancy/filtering sites. The thing is, we have a backup server on a remote location, so I am pretty sure we can set something up with what we have already.
At the moment... (1 Reply)
Discussion started by: edzillion
1 Replies
5. Red Hat
Can anyone recommend an imaging solution for RedHat Linux that would allow base imaging with the ability to do incremental updates and encryption? I know Acronis has a version available, but it is rather pricey.
Thanks. (0 Replies)
Discussion started by: here2learn
0 Replies
6. Solaris
Hello,
Yes, it's me again. Running around getting this done! My current problem is I'm trying to image one drive 0 (/dev/dsk/c1t0d0s0) to drive 1 (/dev/dsk/c1t1d0s0). I know that drive1 came out of a Sun Server and it is a Sun drive. Solaris 10 recognized drive1 after the devfsadm command. The... (8 Replies)
Discussion started by: adelsin
8 Replies
7. AIX
Hi Guys,
I'm working on building a new 595 machine.. I'm try to achieve high availability for the VIO clients using 2 VIO servers, The ethernet part is satisfied using SEA failover, Now how do I achieve redundancy for the disks, its the servers internal disk attached to the scsi cards...
... (2 Replies)
Discussion started by: kkeng808
2 Replies
8. AIX
Have been learning a lot off late and am a little unclear about the VIOS setup particularly with regards to redundancy. Would appreciate your help.
My question is very basic. Lets say I have setup a VIOS and 3 LPARs on only one hdd (non scsi). On what do I setup the second VIOS? Could I for... (7 Replies)
Discussion started by: theaixeman
7 Replies
9. AIX
I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches.
How to make this as a redundancy config?
Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies
URL(4) BSD Kernel Interfaces Manual URL(4)
NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8)
HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
September 18, 2006 BSD