09-19-2001
Well, I figured out the imaging part. The dd command does work, it just takes such a long time I didn't think it was working. I let it run overnight and it finished. Must have taken several hours though. So it looks like using dd for imaging hard drives is possible, just not very practicle.
Having tried a emulating a raid setup with IDE yet. I'll get to that as soon as I have the time and resources. If anyone else has tried it let me know!
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Does anyone know of any good imaging tools that can be used to create an image of a Sco-Unix box? (2 Replies)
Discussion started by: gmrfh1
2 Replies
2. UNIX for Advanced & Expert Users
Dears,
I have server has two port's(Enet0,Enet1) what I want as follows:
Make the two port's has same IP address
where, if the port Enet0 became down automaticly Enet1 become up :confused: .
Amen (4 Replies)
Discussion started by: amen00
4 Replies
3. UNIX for Advanced & Expert Users
Here we want to implement the network redundancy on UNIX with the software.
The two network interface cards are configured on the UNIX node,once one card is down or unnormal,the other can take over. Those aplications that used the tcp ,udp,multicast protocol can also been switched at the same... (2 Replies)
Discussion started by: Frank2004
2 Replies
4. UNIX for Dummies Questions & Answers
We have had some email outages in the last few months and my boss is asking is it worth going with one of those email redundancy/filtering sites. The thing is, we have a backup server on a remote location, so I am pretty sure we can set something up with what we have already.
At the moment... (1 Reply)
Discussion started by: edzillion
1 Replies
5. Red Hat
Can anyone recommend an imaging solution for RedHat Linux that would allow base imaging with the ability to do incremental updates and encryption? I know Acronis has a version available, but it is rather pricey.
Thanks. (0 Replies)
Discussion started by: here2learn
0 Replies
6. Solaris
Hello,
Yes, it's me again. Running around getting this done! My current problem is I'm trying to image one drive 0 (/dev/dsk/c1t0d0s0) to drive 1 (/dev/dsk/c1t1d0s0). I know that drive1 came out of a Sun Server and it is a Sun drive. Solaris 10 recognized drive1 after the devfsadm command. The... (8 Replies)
Discussion started by: adelsin
8 Replies
7. AIX
Hi Guys,
I'm working on building a new 595 machine.. I'm try to achieve high availability for the VIO clients using 2 VIO servers, The ethernet part is satisfied using SEA failover, Now how do I achieve redundancy for the disks, its the servers internal disk attached to the scsi cards...
... (2 Replies)
Discussion started by: kkeng808
2 Replies
8. AIX
Have been learning a lot off late and am a little unclear about the VIOS setup particularly with regards to redundancy. Would appreciate your help.
My question is very basic. Lets say I have setup a VIOS and 3 LPARs on only one hdd (non scsi). On what do I setup the second VIOS? Could I for... (7 Replies)
Discussion started by: theaixeman
7 Replies
9. AIX
I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches.
How to make this as a redundancy config?
Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
mknod(1), chown(1), mount(8), sd(4)
Linux 1992-12-17 HD(4)