03-29-2005
Nowhere in your first post is any mention of the ptest.txt file. It doesn't do me one bit of good to see the output of ls on some random file. Read your own first post. Those are the file whose output I need to see.
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hello,
I don't know what exactly the cause and the solution!!
suddenly I receive this error message when I want to use the 8mm tape drive
"I/O write error"
I disconnect the tape drive and I hook it in another WS and I receive this error :- ... (5 Replies)
Discussion started by: geoquest
5 Replies
2. Solaris
Hi,
I am a newbie to Solaris, I have a SunFire V120 box, i was trying to install a tape drive(HP SureStore DAT24), i did the install in this manner.
# rm -rf /etc/path_to_inst
# init 6
later at the "ok" prompt i gave "boot -ar" after doing that it asked me various options i accepted the... (2 Replies)
Discussion started by: rajendra.rait
2 Replies
3. SCO
i have an ibm machine with dds4 drive running sco. i bought new hp dds4 tape for my back-up. the new tapes are not being read by the system, it says tape error, no such device. i've already clean the drive several times but still the same error occur. i've tried to use the same tape on our windows... (3 Replies)
Discussion started by: yackim
3 Replies
4. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
5. Solaris
Well I have just added new tape drive to my server (lto)
However I am getting few errors in using it. I have checked status with
#iostat -En : giving me few hard errors, few soft errors and execution error.
Also tape status is not visible as "no sense" its coming as "no additional sense".
I... (5 Replies)
Discussion started by: saurabh84g
5 Replies
6. AIX
Hi All
I am trying to copy files present in a partition (server 2) which is mounted to a different server (server 1) as tape drive is connected to it. I ran the below command to copy files within a partition:
svr01:root:/sunfileserver> tar -cvf *
a <foldername>/<filename>/<filename>
a... (4 Replies)
Discussion started by: vathsan
4 Replies
7. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
8. HP-UX
HP rp5450 (L2000)
running HP-UX 11.11B
Using DLT 7000 and DLT 4000 tape drives for nightly full backups
Backup jobs created by SAM
DLT 7000 cron entry is as follows:
00 2 * * 1-6 /usr/sam/lbin/br_backup DLT FULL Y /dev/rmt/0m /var/sam/graphLCAa17036 root Y 1 N > /var/sam/SAM_br_msgs 2>&1... (1 Reply)
Discussion started by: dreh99
1 Replies
LEARN ABOUT REDHAT
amtape
AMTAPE(8) System Manager's Manual AMTAPE(8)
NAME
amtape - user interface to Amanda tape changer controls
SYNOPSIS
amtape config command [ command options ]
DESCRIPTION
Amtape performs tape changer control operations. It uses the underlying tape changer script defined by the tpchanger option for a particu-
lar Amanda configuration as specified by the config argument.
Tape changers maintain a notion of the current and next slot for each configuration. These may or may not correspond to an actual physical
state of the device, but do tend to minimize searching through the tape storage slots. If the desired tape is in the current slot, it is
likely the next tape needed is in the next slot rather than at some random position in the storage slots.
See the amanda(8) man page for more details about Amanda.
COMMANDS
reset Reset the tape changer to a known state. The current slot is set to the first slot. Other device-specific side effects may occur.
Some gravity stackers need to be reset to the top position by hand. This command notifies Amanda the stacker is back in that posi-
tion.
eject If a tape is loaded in the drive, it is ejected and returned to the slot from which it was loaded.
clean If a cleaning tape is defined for the changer, it is used to clean the drive.
show Show the contents of all slots. This can be slow.
label label
Search for and load the Amanda tape with label label.
taper Perform the taper scan algorithm. Load the next tape in the configuration's tape sequence, or a fresh tape with a suitable label.
device Display the name of the current tape device on stdout.
current
Display the current slot.
update Update the changer label database, if it has one, to match the tapes now available.
slot slot
Eject any tape in the drive and put it away, then load the tape from slot slot and reset current.
slot current
Eject any tape in the drive and put it away, then load the tape from the current slot.
slot prev
Eject any tape in the drive and put it away, then load the tape from the previous slot and reset current.
slot next
Eject any tape in the drive and put it away, then load the tape from the next slot and reset current.
slot first
Eject any tape in the drive and put it away, then load the tape from the first slot and reset current.
slot last
Eject any tape in the drive and put it away, then load the tape from the last slot and reset current.
slot advance
Eject any tape in the drive and put it away. Advance current to the next tape, but do not load it.
This is useful with non-gravity stackers to unload the last tape used and set up Amanda for the next run. If you just use eject,
the current tape will be mounted again in the next run, where it will be rejected as being still in use, ejected and the next tape
requested. Using slot next followed by eject does an unnecessary mount.
Note: most changers optimize the slot commands to not eject the loaded tape if it is the one being requested.
AUTHOR
James da Silva <jds@cs.umd.edu>
University of Maryland, College Park
SEE ALSO
amanda(8)
AMTAPE(8)