10-21-2003
I am assuming it is an IDE CDROM? Make sure that the CDROM drive is functional, and recognized. Some BIOSes will not display a boot option for a cdrom if the cdrom drive was not detected properly, or at all. Make sure that Primary Master, Slave and Secondary Master, Slave are all set to 'AUTO'. If all else fails, borrow another cdrom drive to test.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Sup
Ok, here is the problem.
I bought Linux Manrake v.8.1 Power Pack Edition
I booted it up, and got to the partitioning part of the installation. As Manrake users would know, there are several options that you can install with. There is Custom Patitioning, Format and load w/ Linux on it, add... (4 Replies)
Discussion started by: KyPeN
4 Replies
2. UNIX for Dummies Questions & Answers
Edit your /etc/modules.conf file to either remove or comment out the two lines :
alias sound-slot-0 snd-card-intel8x0
above snd-card-intel8x0 snd-pcm-oss
...and replace them with the following line:
alias sound i810_audio
....viola! After saving and rebooting, now I gots da sound!... (0 Replies)
Discussion started by: DownSouthMoe
0 Replies
3. SuSE
ihave mandrake 9.2 (will upgrade soon to 10) but anyways, i can't get the Hard drive or the CD-ROM or Floppy to show up on the desktop. can anyone help me out? (11 Replies)
Discussion started by: linux_newbe
11 Replies
4. Slackware
I am pretty new to Unix/linux and have been itching to use a linux os for a while. And after some research i found that Mandrake was the best for someone like me. I need to know what files i need to download to make a boot disc(s) to make my laptop run only linux. The laptop runs around 200-500mhz... (10 Replies)
Discussion started by: Infidel
10 Replies
5. Linux
Hey everyone,
I'm new to the forum.
I have a problem with Mandrake 8.00; i have installed it on my old PC with no problems (none mentioned) but on re-booting after the installation it just hangs after listing the devices: Hard Disk, CD-ROM & Floppy A.
I have installed it on Packard Bell with... (2 Replies)
Discussion started by: sybella1
2 Replies
6. Solaris
Hi all, i am new in solaris, i have a solris server Ultra 60, when i turn on the server show me the follow error:
Bad magic number in disk label
can`t open disk label package
Boot device: net File and args:
Timeouot waiting for ARP/RARP packet
Timeouot waiting for ARP/RARP packet
....
I... (3 Replies)
Discussion started by: elimunoz
3 Replies
7. UNIX for Dummies Questions & Answers
hi. I am newbie in Unix. I wanted to install Free BSD 5.2.1 to my computer which winXp was already installed. But i couldn't.
I chose Standard. Then it said you are going to use dos style fdisk partitioning. Then a window displayed begining like this.
WARNING: A geometry of 155127/16/63 for... (2 Replies)
Discussion started by: sualcavab
2 Replies
8. Solaris
when i try to build pine unix tells me it can't find make
# ./build xxx
make args are CC=cc soc
Including LDAP functionality
ln: cannot create c-client: File exists
ln: cannot create mtest: File exists
ln: cannot create mailutil: File exists
ln: cannot create imapd: File exists
ln:... (0 Replies)
Discussion started by: vutty81
0 Replies
9. Solaris
Hi all,
I tried to install Sun Solaris 10 on a X-86 based machine. I have dedicated entire diskspace to create auto partition. My hardware config is below:
Main Board : Asus
Processor : Intel 945 , 3 G/Hz
RAM : 1 Gigs
Diskspace : 80 Gigs
When I install, installation goes successful.... (1 Reply)
Discussion started by: naw_deepak
1 Replies
10. Red Hat
I have dexx xps 14.I was installing rhel6.But the installation hanged at following step
initializing hardware detection.................
installion didnt go further (2 Replies)
Discussion started by: shamapraveen
2 Replies
LEARN ABOUT OPENSOLARIS
sdl_cdopen
SDL_CDOpen(3) SDL API Reference SDL_CDOpen(3)
NAME
SDL_CDOpen - Opens a CD-ROM drive for access.
SYNOPSIS
#include "SDL.h"
SDL_CD *SDL_CDOpen(int drive);
DESCRIPTION
Opens a CD-ROM drive for access. It returns a SDL_CD structure on success, or NULL if the drive was invalid or busy. This newly opened CD-
ROM becomes the default CD used when other CD functions are passed a NULL CD-ROM handle.
Drives are numbered starting with 0. Drive 0 is the system default CD-ROM.
EXAMPLES
SDL_CD *cdrom;
int cur_track;
int min, sec, frame;
SDL_Init(SDL_INIT_CDROM);
atexit(SDL_Quit);
/* Check for CD drives */
if(!SDL_CDNumDrives()){
/* None found */
fprintf(stderr, "No CDROM devices available
");
exit(-1);
}
/* Open the default drive */
cdrom=SDL_CDOpen(0);
/* Did if open? Check if cdrom is NULL */
if(!cdrom){
fprintf(stderr, "Couldn't open drive: %s
", SDL_GetError());
exit(-1);
}
/* Print Volume info */
printf("Name: %s
", SDL_CDName(0));
printf("Tracks: %d
", cdrom->numtracks);
for(cur_track=0;cur_track < cdrom->numtracks; cur_track++){
FRAMES_TO_MSF(cdrom->track[cur_track].length, &min, &sec, &frame);
printf(" Track %d: Length %d:%d
", cur_track, min, sec);
}
SDL_CDClose(cdrom);
SEE ALSO
SDL_CD, SDL_CDtrack, SDL_CDClose
SDL
Tue 11 Sep 2001, 22:58 SDL_CDOpen(3)