07-04-2003
I corrected the post
I have removed the email . I did not know about rule 10 while writing email. In future , I'll not write emails
BTW thanks for pointer to disksuite 4.2.1 . It's very useful.
Regards
4 More Discussions You Might Find Interesting
1. Solaris
Hi I have a system that gave me some messages on bootup that I was not used to seeing:
pseudo: pseudo-device: vol0
genunix: vol0 is /pseudo/vol@0
these came with these:
Feb 13 17:42:17 system1 eri: SUNW,eri0 : 100 Mbps full duplex link up
Feb 13 17:42:21 system1sendmail: My unqualified... (0 Replies)
Discussion started by: mndavies
0 Replies
2. UNIX for Advanced & Expert Users
Hi
I tried a tool called mediainfo
> brew info media-info
media-info 0.7.51
http://mediainfo.sourceforge.net
Depends on: pkg-config
/usr/local/Cellar/media-info/0.7.51 (3 files, 14M)
http://github.com/mxcl/homebrew/commits/master/Library/Formula/media-info.rb
Got details from a test... (3 Replies)
Discussion started by: slashdotweenie
3 Replies
3. Red Hat
Hi All,
Could anyone please help to resolve the below problem.
I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error.
I spent 2 days for the above and go through with several suggestion found by googling. But no luck.
... (0 Replies)
Discussion started by: Tanmoy
0 Replies
4. HP-UX
Hi,
Unable to make tape backup, please help.
/opt/ignite/bin/make_tape_recovery -a /dev/rmt/?mn -I -v -m tar -x inc_entire=vg00
* Creating local directories for configuration files and archive.
======= 04/25/16 16:28:08 IST Started /opt/ignite/bin/make_tape_recovery.
(Mon... (4 Replies)
Discussion started by: anuragr
4 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
mknod(1), chown(1), mount(8), sd(4)
Linux 1992-12-17 HD(4)