Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Network card problem, wrong IRQ
Top Forums UNIX for Dummies Questions & Answers Network card problem, wrong IRQ Post 31815 by ripmc on Wednesday 13th of November 2002 05:35:37 PM
Old 11-13-2002
Network card problem, wrong IRQ
I've installed mandrake 9 and from the start my network card wouldn't work. I ran the network configuration wizard several times and counldn't get it to work. I checked Linux and in the boot message said the IRQ for my network card was 0 but wheni checked windows XP it listed it as 23. I have a Realtek RTL8139 Pci card, and its drivers are included in the OS, and linux recongnized it and lists the correct drivers. So i guess i need to change the IRQ setting for this card in linux. Can anyone help on how to do this.
Thanks
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. UNIX for Dummies Questions & Answers

Network Card Problem On Linux

Hi I just installed linux red hat 7.0 and i can't connect the machine on the network. Even after i run linuxconfig, when the machine reboots ethernet card eth0 fails to initialize. Any sugestion would be welcome. (1 Reply)
Discussion started by: IMOTEB
1 Replies

3. UNIX for Dummies Questions & Answers

forcing irq on PCMCIA card

ENV: linux Version: Mandrake 8.1, PCMCIA card: longshine lcs-8534TB. (supported according the PCMCIA docs) laptop is P-II lifetec /etc/sysconfig/pcmcia: PCMCIA=yes PCIC=i82365 ( found via probe -m ) PCIC_OPTS="cs_irq=11 pci_irq_list=11,11 do_scan=0" ( you see i want to force irq 11 )... (3 Replies)
Discussion started by: progressdll
3 Replies

4. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

5. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

6. SCO

3c905b network card problem with SCO 5.0.5

Hi, I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies

7. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

8. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

9. Red Hat

Redhat disabling network interface - IRQ issue

Hi. I'm having problems on multiple Red Hat VM's (on esxi) whereby the network interface IRQ is disabled by the OS. This is the error from dmesg: command: Write(10): 2a 00 03 42 3f e0 00 00 08 00 mptscsih: ioc0: task abort: SUCCESS (sc=ffff81018b45c680) irq 67: nobody cared (try... (0 Replies)
Discussion started by: badoshi
0 Replies

10. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies

LEARN ABOUT DEBIAN

network-admin

network-admin(1)					      General Commands Manual						  network-admin(1)

NAME

       network-admin - Network Administration Tool

SYNOPSIS

       network-admin [OPTION...]

DESCRIPTION

       network-admin is part of the GNOME system tools, a set of tools to easily access and manage system configuration.

       network-admin allows you to specify the way your system connects to other computers and to the Internet.

OPTIONS

       --display=DISPLAY
	      X display to use

       network-admin also accepts the standard GNOME and GTK options.

AUTHORS

       network-admin was written by Carlos Garnacho Parro <garnacho@tuxerver.net> and others.

       This manual page was written by Sven Arvidsson <sa@whiz.se>, for the Debian project (but may be used by others).

SEE ALSO

       services-admin(1), shares-admin(1), time-admin(1), users-admin(1), gtk-options(7), gnome-options(7)

       The online documentation available through the program's Help menu.

GNOME
								    2007-05-08							  network-admin(1)
All times are GMT -4. The time now is 01:32 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy