Sponsored Content
Operating Systems Solaris Issue with Fiber Channel cards in Solaris Post 303043272 by hicksd8 on Thursday 23rd of January 2020 05:08:35 AM
Old 01-23-2020
My first questions are (1) What make/model of storage is it? (2) What make/model of FC cards?

The first place I would be looking is the link configuration(s). The expensive FC cards are highly configurable beasts and the settings need to be compatible with the hardware at the other end of the link. Under pressure, the storage controller might dispatch a packet with a higher payload than the FC card buffer is configured to take causing data to be lost, protocol recovery to be invoked (unsuccessfully), etc, etc.

Have you run an I/O benchmark between Solaris and the storage to see the performance and, more importantly, whether that breaks too.
This User Gave Thanks to hicksd8 For This Post:
 

10 More Discussions You Might Find Interesting

1. Solaris

x25 cards on solaris 8

Has anyone configured one of these things, I cant seem to find any documentation on sunsolve, I want to verify that it is up and running... (1 Reply)
Discussion started by: csaunders
1 Replies

2. Solaris

VxVM/Hba cards/Solaris 10 FS issue

Hi all, I have a compatibly issues with a new hardware My config is the following one : Solaris 10 V490 Hardware 2 X HBA Qlogic 2310f cards An HP EVA 5000 for storage ... Veritas VxVM 4.1 MP1 When I reboot my server, VxVM is trying to mount/use the volume before it's... (0 Replies)
Discussion started by: unclefab
0 Replies

3. HP-UX

Fiber Channel statistic & error level

I need information what maximum error level on FC card need clasification of critical level (SAN mass storidge) Please write screenshot from utility fcutil whith test option. Pawel (0 Replies)
Discussion started by: pawel_ul
0 Replies

4. UNIX for Advanced & Expert Users

How do I know which HBA cards' hardware I have (on Solaris 10) ?

Hi, I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine. The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards. Can anyone suggest how to determine my HBA hardware ? Thanks, Ron. ... (3 Replies)
Discussion started by: ronbarak
3 Replies

5. Solaris

How do I know which HBA cards' hardware I have (on Solaris 10) ?

Hi, I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine. The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards. Can anyone suggest how to determine my HBA hardware ? Thanks, Ron. ... (4 Replies)
Discussion started by: ronbarak
4 Replies

6. Solaris

Fiber Channel StorageTek Array Visible to OS

I installed a FC array for the first time and everything looks OK in mpathadm, cfgadm, but I don't know what to do next. # stmsboot -L non-STMS device name STMS device name ------------------------------------------------------------------ /dev/rdsk/c2t1d0 ... (3 Replies)
Discussion started by: photon
3 Replies

7. Solaris

USCSICMD ioctl calls for Fibre Channel(FC) devices on Solaris 10?

Hi , I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies

8. Solaris

Solaris 10 new fiber connected tape

Hello all, how can i see configured fc tapes in solaris system and how can i install a new fc shared tape device , thanks Best Regards (2 Replies)
Discussion started by: bogacd
2 Replies

9. IP Networking

Channel bonding Issue - Bond0 interface not getting up in on RHEL6

Hello, I am trying to set up Channel Bonding on a RHEL6 Virtual Box VM. I have 2 ethernet cards on the machine which are set up in Internal Network mode. I followed all the steps exactly as mentioned in the RHEL6 deployment Guide, but for some reason i think results are not correct. Here are my... (13 Replies)
Discussion started by: Rohit Bhanot
13 Replies

10. Solaris

Fibre channel link down on booting Solaris server

Hi I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10. After power on the system stops at ok prompt, them I issued the following commands: {0} ok setenv auto-boot? false auto-boot? = false {0} ok reset-all SPARC T3-1B,... (10 Replies)
Discussion started by: fretagi
10 Replies
PODULEBUS(4)						   BSD Kernel Interfaces Manual 					      PODULEBUS(4)

NAME
podulebus -- Acorn Expansion Card bus driver SYNOPSIS
podulebus0 at ioc0 bank 4 (NetBSD/acorn26) podulebus0 at root (NetBSD/acorn32) DESCRIPTION
The podulebus driver handles the expansion-card interface in Archimedes machines and their successors. This includes conventional expansion cards, mini expansion cards (as introduced in the A3000), network expansion cards (as introduced in the A3020), DEBI expansion cards (as introduced in the Risc PC), and Mk II network cards (also introduced in the Risc PC). Drivers for individual cards attach as children of the podulebus device. NetBSD includes several machine-independent expansion card device drivers. There are also some device drivers which are specific to NetBSD/acorn26 or NetBSD/acorn32. HARDWARE
The following devices are supported by NetBSD. SCSI interfaces asc Acorn AKA30, AKA31, and AKA32 SCSI expansion cards (NetBSD/acorn32). cosc MCS Connect32 SCSI interface (NetBSD/acorn32). csa Cumana 8-bit SCSI interface (NetBSD/acorn32). csc Cumana 16-bit SCSI interface (NetBSD/acorn32). hcsc HCCS 8-bit SCSI interface. oak Oak SCSI interface. ptsc Powertec SCSI interface (NetBSD/acorn32). sec Acorn AKA30, AKA31, and AKA32 SCSI expansion cards. Disk controllers dtide D.T. Software IDE controller. hcide HCCS IDE controller. icside ICS IDE controller (NetBSD/acorn32). rapide Yellowstone Educational Solutions RapIDE IDE controller (NetBSD/acorn32). simide Simtec IDE controller (NetBSD/acorn32). Network interfaces ea Atomwide A-10xx and Acorn AEH54 Ethernet cards (Ether3). eb Atomwide and ANT network-slot and Acorn AEH61 Ethernet cards (EtherB). eh i-cubed EtherLan 100-, 200- and 500-series, and Acorn AEH75, AEH77, and AEH79 Ethernet cards (EtherH) (NetBSD/acorn26). ei Acorn AKA25 Ethernet card (Ether1). ie Acorn AKA25 Ethernet card (Ether1) (NetBSD/acorn32). ne Various vaguely NE2000-compatible Ethernet cards (NetBSD/acorn32). Serial interfaces amps Atomwide multi-port serial interface (NetBSD/acorn32). SEE ALSO
acorn26/eh(4), acorn32/asc(4), acorn32/cosc(4), acorn32/csc(4), acorn32/ie(4), acorn32/ptsc(4), dtide(4), ea(4), eb(4), ei(4), hcide(4), ne(4), oak(4), sec(4) BUGS
Too few drivers are shared between NetBSD/acorn26 and NetBSD/acorn32. BSD
October 26, 2006 BSD
All times are GMT -4. The time now is 03:18 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy