SEC(4) BSD Kernel Interfaces Manual SEC(4)NAME
sec -- Acorn SCSI Expansion Card driver
SYNOPSIS
sec* at podulebus0 slot ?
scsibus* at sec?
DESCRIPTION
The sec driver supports the Acorn SCSI Expansion Card, model numbers AKA30, AKA31, and AKA32. These cards support 8-bit parallel synchronous
transfers at up to 4 MHz.
SEE ALSO podulebus(4), scsi(4)BSD October 1, 2006 BSD
Check Out this Related Man Page
NSP(4) BSD Kernel Interfaces Manual NSP(4)NAME
nsp -- Workbit Ninja SCSI-3 based PC-Card SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device nsp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
nsp_load="YES"
DESCRIPTION
The nsp driver provides access to the SCSI bus connected to a PC-Card SCSI host adapter based on a Ninja SCSI-3 controller by Workbit.
HARDWARE
Controllers supported by the nsp driver include:
o Alpha-Data AD-PCS201
o I-O DATA CBSC16
SEE ALSO cd(4), ch(4), da(4), intro(4), pccard(4), sa(4), scsi(4)HISTORY
The nsp driver has been developed for NetBSD/pc98 and ported for FreeBSD. It first appeared in FreeBSD 3.4 with PAO3 and merged in
FreeBSD 4.2.
AUTHORS
The nsp driver was written by Naofumi HONDA.
This manual page was written by Noriaki MITSUNAGA <non@FreeBSD.org> and Hideyuki KURASHINA <rushani@FreeBSD.org>.
BUGS
SMIT mode is only supported under OLDCARD now.
BSD August 8, 2004 BSD
Hi everyone,
I am a new comer in this forum.
When I try to send email in my Linux machine with command "mail" or "sendmail", I always find it include the IP address of my machine in the email header. Does anybody know how to eliminate this IP address or replace it with a fake one in the email... (20 Replies)
Hi All,
i have an input below.
As long as "x= 1" , i would want to capture 2 lines using sed or awk
for eg :
0001 x= 1 $---------------------------------..-.--..
0001 tt= 137 171 423 1682 2826 0
Pls help. Thanks in advance.
Note that the number of lines in each block do... (37 Replies)
Im trying to get the frist two line of a file as a variables.
input file
/tmp/tmp.txt
1226037463l
1226037422ll
while read -r LINE
do
if ;
then
FRIST=`echo $LINE | awk -F"|" 'NR==1''{print $1}'`
echo $FRIST
SECOND=`echo $LINE | awk -F"|"... (37 Replies)
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
I'm having an issue with SSH on a server that hasn't had any configuration changes made on it in a long time. I SSH to the server and it hangs at "debug1: SSH2_MSG_KEXINIT sent" for exactly 40 seconds then connects fine after that pause. Everything I have found points to DNS, but I use host files... (19 Replies)
Hi!
I have a debian linux VPS and i am wondering how would someone be able to hack into it , in what ways ?
I've asked a more knowledgeable friend and he said the only way someone would be able to get into my VPS is via FTP or SSH, are there some other ways someone can enter my machine ?
I... (18 Replies)
I have lines like:
table10 table_name_10 table10 table_name_10
table20 table_name_20 table20 table_name_20
table30 table_name_30 table30 table_name_30
I want to change the second "table_names" in all lines to test_table_name. Required output would be:
table10 table_name_10 table10... (19 Replies)
Hi,
I'd like to intersect two files by the 4th col of the first file and 6th col of the second file. This is the code I use:
awk 'NR==FNR{A;next}$6 File1 File2
However, this is only outputting the second file lines. I'd like to have both lines in a single line separated by a tab.
Thanks in... (25 Replies)
I have Ubuntu 16.04 (dual boot with Windows 10) and a HP Spectre x360 laptop.
I have recently bought a Dell Ultrasharp U2515H monitor, which I connect via a Dell docking station.
When I plug the docking station to my laptop on Windows, both monitors are detected and everything works fine.
... (23 Replies)
I am new to grep and Linux and am looking to see if grep can parse out a list of lines that have a difference of more than 10 seconds between the times on each line.
Example
2016-09-17 19:30:57 INFO: id: 4562079216, time: 2016-09-17 19:30:41,
2016-09-17 12:02:26 INFO: id:... (26 Replies)
]I would like to make the second file label 'b' print down the first file label 'a', like shifting down the file creating new lines I want it to print all the way down until the first line of the second file hit the last line of the first file. Would I have to put this into a file itself or could I... (24 Replies)
You are seeing this new video here first!
Top Five Cybersecurity Threats | Earth Year 2019 | You Have Been Warned!
https://youtu.be/dRE4u9QVsSg
PS: That video has two small typos, but nothing serious. Heck it took nearly 1.5 hours to render even on a 12-core Mac Pro with 64GB of... (20 Replies)