It depends quite what you are looking for. Do any of these help (sorry but I no longer have access to AIX so I'm a bit rusty!)
What are the metrics you are looking for? Is it the LPAR view of the assigned disk to the size of the disk that is owned by the hardware as a whole? The LPAR will not see that.
I hope that these suggestions give you something.
Robin
Thank Robin, I would like to check at the physical hardware console, not from LPAR, have not LPAR right now.
--- Post updated at 06:13 AM ---
Quote:
Originally Posted by zxmaus
from the hardware itself, you cannot see the disks - you can only see the controllers, not what is attached to them.
As part of the SMS menu you can see the disks and sizes if you query the controllers - or when you install AIX as you have to select a suitable disks for the installation - with location code.
If you have AIX already installed, run these commands.
to find your SAS disks, run
to figure out the disk size of said disks use
Hi Zxmaus,
I understand now that from physical hardware Power Machine we cannot check the disk and size.
Still have 1 thing to ask, for SAS disk, I see it is part of raid controller. The disk is called pdisk. After configuring raid, it becomes hdisk which AIX can see. The question is, if in the first time, we assign the controller and its disks to LPAR to install AIX. How can we configure the raid before AIX OS can see these disks?
I have two Unix machines on the network and now one of them are running out of disk but i have alot on the other so i like to mount the disk (or a folder) from the one that has disk and mount it on the other that does not.
How do i do that? Is it possible i read the "man mount" but didn't really... (5 Replies)
Hi!!
I am these days working on a project, where I need to know about the disk controllers available in a machine (e.g., 3ware,IBM,etc).
Please, let me know the command by which I can get the information.
thnx,
priyanka (3 Replies)
Hello All,
Can anybody please tell me what is the maximum limit of Physical IBM Power Machine which can be handled by single HMC at a single point of time?
Thanks,
Jenish (1 Reply)
Hello,
I have a quick question regarding POWER HA ( HACMP ) 5.5 ;
I have four ethernet adapters
en0
en1
en2
en3
en0 is configured as BOOT_IP with IP address
all other ethernet adapters are empty en1 / en2 / en3
so when I configure the service IP and start HACMP , the service IP... (2 Replies)
Hi,
Is there an easy way to find the disk-type from the command line or with another api ? sdparm works for SAS but not for SATA, hdparm works for SATA but not SAS.
Thanks (1 Reply)
hi guys,
I don't like the new concept of the power ha 7 cluster with the repository disk and the internal solidb, I really would like to mirror this disk, but the "IBM PowerHA SystemMirror 7.1 for AIX" redbook says, normal lvm operations should not be performed on this disk.
even mirroring the... (0 Replies)
Hi
Is there any native commands or somewhere in the /proc files to get the machine's power consumption? I googled for a while and cannot really find this information
Thanks for your help. (6 Replies)
I need to add a VMware virtual disk to the 99-oracle-asmdevices.rules file but the OS is not assigning a WWID to the disk. It has been fdisk'd and a single partition created.
What TAG inside the file needs to be added? the Program scsi-id does not work for some reason. latest patches... (0 Replies)
Hi,
I have installed the HMC on the VMWare VM. I try to add the power machine (managed system) and asking for a password? So this is the IBM predefined password of Power Machine?
In the VMWare perspective, we can login to ESX host to do some management tasks. But how about the Power machine?... (6 Replies)
OSLevel: 5300-10-02-0943
System Model: IBM,8203-E4A
Power 6
==
Hi!
I replaced a failed pdisk in the raid enclosure as follows,
- rmdev -l 'pdisk18' '-d'
- Replaced it.
- cfgmgr (detected)
- I can see the new drive, with the correct serial #
lscfg -v -l pdisk18
pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies
LEARN ABOUT NETBSD
bio
BIO(4) BSD Kernel Interfaces Manual BIO(4)NAME
bio -- Block IO ioctl tunnel pseudo-device
SYNOPSIS
pseudo-device bio
DESCRIPTION
The bio driver provides userland applications ioctl(2) access to devices otherwise not found as /dev nodes. The /dev/bio device node oper-
ates by delegating ioctl calls to a requested device driver. Only drivers which have registered with the bio device can be accessed via this
interface.
The following device drivers register with bio for volume management:
arcmsr(4) Areca Technology Corporation SATA RAID controller
cac(4) Compaq RAID array controller
ciss(4) Compaq Smart ARRAY 5/6 SAS/SATA/SCSI RAID controller
mfi(4) LSI Logic & Dell MegaRAID SAS RAID controller
The following ioctl calls apply to the bio device:
BIOCLOCATE Locate a named device and give back a cookie to the application for subsequent ioctl calls. The cookie is used to tunnel
further ioctls to the right device.
BIOCINQ Retrieve number of volumes and physical disks for a specific device.
BIOCDISK Retrieve detailed information for the specified physical disk. Information returned can include status, size, channel,
target, lun, vendor name, serial number, and processor device (ses).
BIOCDISK_NOVOL Is just the same as BIOCDISK but doesn't require the disks to be in volume sets, so this applies to any physical disk con-
nected to the controller.
Note: this ioctl might not be supported on all hardware.
BIOCVOL Retrieve detailed information for the specified volume. Information returned can include status, size, RAID level, number
of disks, device name association (sd?) and vendor name.
BIOCALARM Control the alarm beeper on the device. Supported states are: disable alarm, enable alarm, silence alarm, status and test
alarm.
Note: These options might not be supported on all hardware.
BIOCBLINK Blink an LED of the specified physical disk. Supported blink states are: blink LED, unblink LED and blink alarm LED.
Note: This option is only supported if the disk is governed by ses(4) and the hardware supports hardware blinking.
BIOCSETSTATE Alter the state of specified physical disk. Supported states are: create/remove hot-spare, create/remove pass through
disk, start/stop consistency check in a volume, online disk and offline disk.
Note: These options might not be supported on all hardware.
BIOCVOLOPS For operations in volume sets. It's able to create and remove a volume set in a supported RAID controller.
Note: this ioctl might not be supported on all hardware.
FILES
/dev/bio ioctl tunnel device
SEE ALSO ioctl(2), bioctl(8)HISTORY
The bio driver first appeared in OpenBSD 3.2 and NetBSD 4.0.
AUTHORS
The bio driver was written by Niklas Hallqvist <niklas@openbsd.org>. The API was written by Marco Peereboom <marco@openbsd.org> and was
extended even more for NetBSD by Juan Romero Pardines <xtraeme@netbsd.org>.
BSD May 25, 2008 BSD