BOOTPD(8)						    BSD System Manager's Manual 						 BOOTPD(8)

NAME

     bootpd, bootpgw -- Internet Boot Protocol server/gateway

SYNOPSIS

     bootpd [-i | -s] [-c chdir-path] [-d level] [-h hostname] [-t timeout] [bootptab [dumpfile]]
     bootpgw [-i | -s] [-d level] [-h hostname] [-t timeout] server

DESCRIPTION

     The bootpd utility implements an Internet Bootstrap Protocol (BOOTP) server as defined in RFC951, RFC1532, and RFC1533.  The bootpgw utility
     implements a simple BOOTP gateway which can be used to forward requests and responses between clients on one subnet and a BOOTP server (i.e.
     bootpd) on another subnet.  While either bootpd or bootpgw will forward BOOTREPLY packets, only bootpgw will forward BOOTREQUEST packets.

     One host on each network segment is normally configured to run either bootpd or bootpgw from inetd(8) by including one of the following lines
     in the file /etc/inetd.conf:

	   bootps dgram udp wait root /usr/libexec/bootpd bootpd /etc/bootptab
	   bootps dgram udp wait root /usr/libexec/bootpgw bootpgw server

     This mode of operation is referred to as "inetd mode" and causes bootpd (or bootpgw) to be started only when a boot request arrives.  If it
     does not receive another packet within fifteen minutes of the last one it received, it will exit to conserve system resources.  The -t option
     controls this timeout (see OPTIONS).

     It is also possible to run bootpd (or bootpgw) in "standalone mode" (without inetd(8)) by simply invoking it from a shell like any other reg-
     ular command.  Standalone mode is particularly useful when bootpd is used with a large configuration database, where the start up delay might
     otherwise prevent timely response to client requests.  (Automatic start up in standalone mode can be done by invoking bootpd from within
     /etc/rc.local, for example.)  Standalone mode is less useful for bootpgw which has very little start up delay because it does not read a con-
     figuration file.

     Either program automatically detects whether it was invoked from inetd or from a shell and automatically selects the appropriate mode.  The
     -s or -i option may be used to force standalone or inetd mode respectively (see OPTIONS).

OPTIONS

     The following options are available:

     -t timeout
	     Specify the timeout value (in minutes) that a bootpd or bootpgw process will wait for a BOOTP packet before exiting.  If no packets
	     are received for timeout minutes, then the program will exit.  A timeout value of zero means "run forever".  In standalone mode, this
	     option is forced to zero.

     -d debug-level
	     Set the debug-level variable that controls the amount of debugging messages generated.  For example, -d4 or -d 4 will set the debug-
	     ging level to 4.  For compatibility with older versions of bootpd, omitting the numeric parameter (i.e., just -d) will simply incre-
	     ment the debug level by one.

     -c chdir-path
	     Set the current directory used by bootpd while checking the existence and size of client boot files.  This is useful when client boot
	     files are specified as relative pathnames, and bootpd needs to use the same current directory as the TFTP server (typically
	     /tftpboot).  This option is not recognized by bootpgw.

     -h hostname
	     Specify the hostname corresponding to the IP address to listen on.  By default, bootpd listens on the IP address corresponding to the
	     machine's hostname, as returned by gethostname(3).

     -i      Force inetd mode.	This option is obsolete, but remains for compatibility with older versions of bootpd.

     -s      Force standalone mode.  This option is obsolete, but remains for compatibility with older versions of bootpd.

     bootptab
	     Specify the name of the configuration file from which bootpd loads its database of known clients and client options (bootpd only).

     dumpfile
	     Specify the name of the file that bootpd will dump its internal database into when it receives a SIGUSR1 signal (bootpd only).  This
	     option is only recognized if bootpd was compiled with the -DDEBUG flag.

     server  Specify the name of a BOOTP server to which bootpgw will forward all BOOTREQUEST packets it receives (bootpgw only).

OPERATION

     Both bootpd and bootpgw operate similarly in that both listen for any packets sent to the bootps port, and both simply forward any BOOTREPLY
     packets.  They differ in their handling of BOOTREQUEST packets.

     When bootpgw is started, it determines the address of a BOOTP server whose name is provided as a command line parameter.  When bootpgw
     receives a BOOTREQUEST packet, it sets the "gateway address" and "hop count" fields in the packet and forwards the packet to the BOOTP server
     at the address determined earlier.  Requests are forwarded only if they indicate that the client has been waiting for at least three seconds.

     When bootpd is started it reads a configuration file, (normally /etc/bootptab) that initializes the internal database of known clients and
     client options.  This internal database is reloaded from the configuration file when bootpd receives a hangup signal (SIGHUP) or when it dis-
     covers that the configuration file has changed.

     When bootpd receives a BOOTREQUEST packet, it looks for a database entry matching the client request.  If the client is known, bootpd com-
     poses a BOOTREPLY packet using the database entry found above, and sends the reply to the client (possibly using a gateway).  If the client
     is unknown, the request is discarded (with a notice if debug > 0).

     If bootpd is compiled with the -DDEBUG option, receipt of a SIGUSR1 signal causes it to dump its internal database to the file
     /tmp/bootpd.dump or the dumpfile specified as a command line parameter.

     During initialization, both programs determine the UDP port numbers to be used by calling getservbyname(3) (which normally uses
     /etc/services).  Two service names (and port numbers) are used:

	   bootps BOOTP Server listening port
	   bootpc BOOTP Client destination port

     If the port numbers cannot be determined using getservbyname(3) then the values default to bootps=67 and bootpc=68.

FILES

     /etc/bootptab     Database file read by bootpd.
     /tmp/bootpd.dump  Debugging dump file created by bootpd.
     /etc/services     Internet service numbers.
     /tftpboot	       Current directory typically used by the TFTP server and bootpd.

SEE ALSO

     bootptab(5), inetd(8), tftpd(8)

     DARPA Internet Request For Comments:
     RFC951   Bootstrap Protocol
     RFC1532  Clarifications and Extensions for the Bootstrap Protocol
     RFC1533  DHCP Options and BOOTP Vendor Extensions

AUTHORS

     This distribution is currently maintained by Walter L. Wimer <walt+@cmu.edu>.

     The original BOOTP server was created by
     Bill Croft at Stanford University in January 1986.

     The current version of bootpd is primarily the work of
     David Kovar,
     Drew D. Perkins, and
     Walter L. Wimer, at Carnegie Mellon University.

     Enhancements and bug-fixes have been contributed by:

     (in alphabetical order)

     Danny Backx <db@sunbim.be>
     John Brezak <brezak@ch.hp.com>
     Frank da Cruz <fdc@cc.columbia.edu>
     David R. Linn <drl@vuse.vanderbilt.edu>
     Jim McKim <mckim@lerc.nasa.gov>
     Gordon W. Ross <gwr@mc.com>
     Jason Zions <jazz@hal.com>.

BUGS

     Individual host entries must not exceed 1024 characters.

BSD
								 February 10, 2004							       BSD