Likely you are seeing an IP alias, that's why you have two ip's on the same adapter.
Now, as to two adapters with same IP, one could be disconnected at the physical layer.
**EDIT again. You can assign an IP to the ETherChannel adapter, and then the parent adapter. But its not a good way to go about it. That actually looks like what is happening here. Or someone tried to remove a backup adapter from the EtherChannel and gave it the IP.
How can I see where the alias IP is configured?
Quote:
To be honest, I'm not even sure where to begin with cleaning this up, or how far you want to go.
I can go very far
Could you shed some light on the parent Ether and child Ether?
And also with this, et is not used for IP address?
Quote:
et is used for IEE 802.3
--- Post updated at 05:18 AM ---
Hello,
After cleaning up, it's birghter
But I not yet find out where the alias IP (either 10.176.x.65 or 10.176.x.127) is configured.
I need to delete a TTY in my AIX 4.3 system. I have tried using the smit but everytime I try it, there is a message telling me that the device is in use and cannot be changed. How do I take the device "offline", so to speak, so that I can edit the settings and/or delete it.
V/R
Djassi (3 Replies)
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi, I have the following packages installed on my AIX server
xlC.aix50.rte 10.1.0.2 COMMITTED XL C/C++ Runtime for AIX 5.3
xlC.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.cpp 9.0.0.0 COMMITTED C for AIX Preprocessor
xlC.msg.en_US.rte 10.1.0.2 COMMITTED XL C/C++ Runtime
xlC.rte... (4 Replies)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a... (1 Reply)
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only.
... (1 Reply)
Discussion started by: alphatron150
1 Replies
LEARN ABOUT MINIX
ifconfig
IFCONFIG(8) System Manager's Manual IFCONFIG(8)NAME
ifconfig - configure a TCP/IP device
SYNOPSIS
ifconfig [-I ip-device] [-h ipaddr] [-n netmask] [-iv]
DESCRIPTION
Ifconfig initializes a TCP/IP device setting the IP address and/or netmask. It will report the address and netmask set. This command may
be used if the system has not been configured properly yet. It is only used at boot time to set a fixed address for a system without a
physical ethernet. Normally the inet task will find it out by itself from the RARP server.
OPTIONS -h The decimal TCP/IP address to set.
-n The netmask to set.
-i Don't set the IP address or netmask if already set. This way ifconfig cannot interfere if the numbers have been found out by RARP.
-v Report IP address and netmask. This is the default action if there are no other options.
SEE ALSO hostaddr(1), rarpd(8), set_net_default(8), boot(8).
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
IFCONFIG(8)