Sponsored Content
Operating Systems Solaris Solaris can not boot because metadb lost Post 303008715 by DukeNuke2 on Tuesday 5th of December 2017 05:40:39 AM
 

10 More Discussions You Might Find Interesting

1. Solaris

solaris boot problem boot error loading interpreter(misc/krtld)

When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error. cannot find mis/krtld boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies

2. Solaris

solaris with metadb

Hi All, If solaris has metadb services on the disk, it means that it has a HW raid controller. Or what. Thanks in advance. (1 Reply)
Discussion started by: itik
1 Replies

3. Solaris

metadb problem - server unable to boot

Hi everyone I have a problem. My configuration is as follows: Sun 280R server 2 x internal disks 3 x state databases on disk 1 3 x state databases on disk 2 Disk 1 was giving errors, so I cleared the mirrors on it, deleted the state databases and replaced the disk. Before attaching... (5 Replies)
Discussion started by: soliberus
5 Replies

4. Solaris

Solaris x86 installation using jumpstart does not local boot ( boot from hdd)

I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies

5. Solaris

How to create metadb with zpool in Solaris 11

Hi, my root pool is as follows. How can I create a metadb if I want to create SVM volumes? zpool status pool: rpool1 state: ONLINE scan: none requested config: NAME STATE READ WRITE CKSUM rpool1 ONLINE 0 0 0 c4t1d0s0 ... (10 Replies)
Discussion started by: incredible
10 Replies

6. What is on Your Mind?

Lost Sun Solaris 10Certification

.............. (1 Reply)
Discussion started by: siddulamadhu
1 Replies

7. Solaris

Boot disk crash with metadb config info

Hello all; We have a SunFire V240 with three disks that were part of a metadb. One of those disks, the boot disk, experienced a horrible death Monday night and we're now trying to recover from that. I know very little about metadb stuff, so please be gentle with me... I'm assuming... (3 Replies)
Discussion started by: Handon
3 Replies

8. Solaris

Check Solaris VM Databases metadb does not have enough information about logical volumes

Check Solaris VM Databases metadb does not have enough information about logical volumes. Current value is 0% I have checked the SVM status, all disks are good state and synched perfectly. no errors in metadb -i. what is this alert exact mean? what we have to check for the value? Please... (1 Reply)
Discussion started by: Naveen.6025
1 Replies

9. Solaris

Solaris 10 Volume Manager - adding slice to metadb

Hi all, I added a new disk slice to the current metadb. Below is what I see bash-3.2# metadb -i flags first blk block count a m p luo 16 8192 /dev/dsk/c0t0d0s7 a p luo 8208 8192 ... (3 Replies)
Discussion started by: javanoob
3 Replies

10. Solaris

Solaris stuck during boot after reconfigure boot

Hello, I have a problem with my machine that won't boot properly. The story is that I installed a software called apcupsd, which is a control application for my APC battery UPS. I have used version 3.14.10 earlier, but as part of restoring my previously crashed os harddrive I wanted to... (18 Replies)
Discussion started by: Zorken
18 Replies
URL(4)							   BSD Kernel Interfaces Manual 						    URL(4)

NAME
url -- Realtek RTL8150L USB Ethernet driver SYNOPSIS
url* at uhub? urlphy* at mii? DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip. The url driver supports the following adapters: CompUSA USBKR100 GreenHouse GH-USB100B Melco Inc. LUA-KTX Sitecom LN013 For more information on configuring this device, see ifconfig(8). DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8) HISTORY
The url device driver first appeared in NetBSD 1.6. AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>. BSD
September 18, 2006 BSD
All times are GMT -4. The time now is 09:30 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy