11-01-2016
You haven't added the Broadcom device yet? Is this because you tried, and the device is not either of the ones for which there is a SCO driver.
HP does not have any SCO drivers for the z400.
For the Realtek card you probably have to supply the PCI Slot number, the Bus Number and the Device Number. These are sometimes available in the CMOS, or are displayed during POST.
This User Gave Thanks to jgt For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
2. SCO
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
Discussion started by: tpurazi1
1 Replies
3. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
4. SCO
Hello Guys,
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
Discussion started by: nrcuevas
2 Replies
5. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
6. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
8. UNIX for Dummies Questions & Answers
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies
9. SCO
hi
i installed sco unix open server 5.0.7 on virtual machine vmware and runing it,
its work perfect and good.
now how i can configuare network at scoadmin that i able to access nework ?
---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ----------
nobody can... (2 Replies)
Discussion started by: farzad226
2 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
NE(4) BSD Kernel Interfaces Manual NE(4)
NAME
ne -- NE2000 and compatible Ethernet cards device driver
SYNOPSIS
ISA boards
ne0 at isa? port 0x280 irq 9
ne1 at isa? port 0x300 irq 10
ne* at isapnp?
MCA boards
ne* at mca? slot ?
PCI boards
ne* at pci? dev ? function ?
PCMCIA
ne* at pcmcia? function ?
acorn32
ne* at podulebus?
amiga
ne* at zbus0 # AriadneII, X-surf
amigappc
ne* at zbus0 # AriadneII, X-surf
atari
ne0 at mainbus0 # EtherNEC on Atari ROM cartridge slot
evbarm
ne0 at obio? addr 0x0e000200 intr 5 # on-board Asix AX88796
evbsh3
ne0 at mainbus? # Realtek RTL8019AS
x68k
ne* at intio0 addr 0xece300 intr 249 # Nereid Ethernet
ne* at intio0 addr 0xeceb00 intr 248 # Nereid Ethernet
neptune0 at intio0 addr 0xece000 intr 249 # Neptune-X
neptune1 at intio0 addr 0xece400 intr 249 # Neptune-X at alt. addr.
ne* at neptune? addr 0x300
DESCRIPTION
The ne device driver supports NE2000 and compatible (including NE1000) Ethernet cards. While the original NE2000 is designed for ISA bus,
the compatible Realtek 8019 chip is widely used on various local busses and ne driver also supports such devices on various machines.
MEDIA SELECTION
The Realtek 8019 (ISA, ISAPnP, some PCMCIA) and Realtek 8029 (PCI) NE2000-compatible Ethernet chips include support for software media selec-
tion. If one of these chips is detected by the driver, the list of supported media will be displayed.
For all other chips supported by the ne driver, media selection must be performed either via card jumper settings or by vendor-supplied con-
figuration programs.
DIAGNOSTICS
ne0: where did the card go? The driver found the card, but was unable to make the card respond to complete the configuration sequence.
SEE ALSO
ifmedia(4), intro(4), isa(4), isapnp(4), mca(4), pci(4), pcmcia(4), ifconfig(8)
BSD
April 3, 2010 BSD