|
|
Sponsored Content
Contact Us
Post Here to Contact Site Administrators and Moderators
Lost my Post / Thread
Post 302968035 by greycells on Wednesday 2nd of March 2016 08:14:00 PM
03-02-2016
|
|
8 More Discussions You Might Find Interesting
1. Post Here to Contact Site Administrators and Moderators
I am not getting post new thread button when i was logged in.
tell me how to do this.
i want to print data between two lines in a file into another file. which command should i use in UNIX (0 Replies)
Discussion started by: kamesh83
0 Replies
2. Forum Support Area for Unregistered Users & Account Problems
I can not Post a Thread. (1 Reply)
Discussion started by: spiderman3k
1 Replies
3. Forum Support Area for Unregistered Users & Account Problems
How do I post a new thread?
I see no place to do this and it must have existed at one time since I have posted before. (1 Reply)
Discussion started by: Gale Gorman
1 Replies
4. Post Here to Contact Site Administrators and Moderators
Im new to this forum. can you guide me how to post a new thread.
Thanks in advance
Hari (3 Replies)
Discussion started by: Hari123
3 Replies
5. Post Here to Contact Site Administrators and Moderators
Hi,
yesterday I have got reply in my thread
how to redirect shell pipe to 2 pipes.
I would read that answer once again,
as my re.re. is also lost
Jack (6 Replies)
Discussion started by: jack2
6 Replies
6. Post Here to Contact Site Administrators and Moderators
Hi scoot
Hope you are doing well!!
I didn't post any new thread, is their any problem in my access
could you please check it and let me know.
Previously posted threads was one of my interview question and i didn't understand how to solve , i am a new for shell script, i didn't find any help... (2 Replies)
Discussion started by: ksakil
2 Replies
7. Forum Support Area for Unregistered Users & Account Problems
Dear Moderator
I am not able to post any new thread or post reply to mine old thread.
Kindly help as i am stuck on one problem and needed suggestion.
Regards
Jaydeep (1 Reply)
Discussion started by: jaydeep_sadaria
1 Replies
8. Post Here to Contact Site Administrators and Moderators
Just joined and registered 15 minutes ago.
Can't figure out how to post a new question about 'grep'
I searched and found that I need to click the 'New Thread' button, I couldn't see any 'New Thread' buttons anywhere, so I searched around and ended up here where I DO see a 'new thread' button....... (3 Replies)
Discussion started by: TuftyDave
3 Replies
LEARN ABOUT NETBSD
url
URL(4) BSD Kernel Interfaces Manual URL(4) NAME
url -- Realtek RTL8150L USB Ethernet driver SYNOPSIS
url* at uhub? urlphy* at mii? DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip. The url driver supports the following adapters: CompUSA USBKR100 GreenHouse GH-USB100B Melco Inc. LUA-KTX Sitecom LN013 For more information on configuring this device, see ifconfig(8). DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8) HISTORY
The url device driver first appeared in NetBSD 1.6. AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>. BSD
September 18, 2006 BSD