Hi,
I have broken my laptop hard drive so I would like to put it in an external box to backup my documents.
I have a doubt whether the interface of the hard disk is sata or ide.
Inside notes attached, is reported "controller SATA AHCI" but on the model section is given IDE hard disk
Hi experts,
I need to determine if I have 4GB free space on my UNix server? Is there a way that I can do it instead of executing df -k . in each folder?
Thanks for your help. (3 Replies)
:eek: I use this Solaris to run CMS a call acounting software package for my job. No one could run reports today because it said the this when you logged on
"The following file systems are low, and could adversely affect server performance:
File system /: 99%full"
Can some one please explain... (9 Replies)
Hi,
I can't make the network connection. The cable and hub should be fine since they are working on other systems. I've used 'mktcpip' as well as 'smit tcpip' to configure the interface, and was able to ping the system itself, but I can not ping the gateway - no response. After reboot, the IP... (1 Reply)
Hi,
I have a failed hard disk in my Sun Fire V240. Unfortunately it does not show up in 'cfgadm -al' or in the format command so I cannot unconfigure it and illuminate the blue light on the front to identify it. Is there any way of iluminating the blue lights on the other disks so I can at... (3 Replies)
hi
I've a fresh installation of SCO 5.0.7 on the IDE hard disk.
For SCSI hard disk I can declare, for example blc disk driver using:
# mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Good Evening,
2 years ago, I set up an Ubuntu file-server for a friend, who is a photograph amateur. Basically, the server offers a software RAID-5 that can be accessed remotely from a MAC. Unfortunately, I didn't labeled the hard drives (i.e. which physical drive corresponds to the /dev/sdX... (2 Replies)
Hello,
Currently we have a Oracle X4100 ( Solaris 10 ) server with disk failure. Originally our hardware team thought the disk can be hot-swap, when they stood in front of the server, none of the disk failure LED were on, so now we have no idea which disk is the bad one for replacement.
As... (2 Replies)
I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX.
it has one ldom created on it
luxadm probe output ---
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node... (7 Replies)
Discussion started by: kpatel786
7 Replies
LEARN ABOUT NETBSD
jmide
JMIDE(4) BSD Kernel Interfaces Manual JMIDE(4)NAME
jmide -- JMicron Technology JMB36x PCIe to SATA II/PATA controller driver
SYNOPSIS
jmide* at pci? dev ? function ? flags 0x0000
ahcisata* at jmide?
DESCRIPTION
The jmide driver supports the JMicron Technology JMB36x IDE controllers.
These PCI-e controllers exist in different flavors (1 or 2 PATA Ultra/133 ports and/or 1 or 2 SATA-II ports), and are highly flexible. The
SATA ports can be attached to the integrated AHCI controller or attached to the PCI IDE channels in PATA emulation, in either single-drive
emulation on each PCI IDE channels, or in master/slave emulation on one of the PCI IDE channels.
When enabled, the AHCI controller can either be on the PCI function 0 or function 2. The PCI IDE controller can also be on either PCI func-
tion, and can share the PCI function with AHCI. The jmide driver supports both the AHCI controller and PCI IDE controller in various config-
urations.
SEE ALSO ahcisata(4), ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)AUTHORS
The jmide driver was written by Manuel Bouyer.
BSD July 2, 2007 BSD