Hi,
I can't make the network connection. The cable and hub should be fine since they are working on other systems. I've used 'mktcpip' as well as 'smit tcpip' to configure the interface, and was able to ping the system itself, but I can not ping the gateway - no response. After reboot, the IP disappears from the interface. Here are some output. Please help. Thank you!
Code:
root@aix# ifconfig -a
en0: flags=4e080863,80<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST,GROUPRT,64BIT,PSEG,CHAIN>
lo0: flags=e08084b<UP,BROADCAST,LOOPBACK,RUNNING,SIMPLEX,MULTICAST,GROUPRT,64BIT>
inet 127.0.0.1 netmask 0xff000000 broadcast 127.255.255.255
inet6 ::1/0
tcp_sendspace 131072 tcp_recvspace 131072 rfc1323 1
root@aix# entstat en0
-------------------------------------------------------------
ETHERNET STATISTICS (en0) :
Device Type: IBM 10/100 Mbps Ethernet PCI Adapter (23100020)
Hardware Address: 00:06:29:c3:41:c5
Elapsed Time: 0 days 0 hours 0 minutes 41 seconds
Transmit Statistics: Receive Statistics:
-------------------- -------------------
Packets: 1 Packets: 0
Bytes: 590 Bytes: 0
Interrupts: 0 Interrupts: 0
Transmit Errors: 0 Receive Errors: 0
Packets Dropped: 0 Packets Dropped: 0
Bad Packets: 0
Max Packets on S/W Transmit Queue: 1
S/W Transmit Queue Overflow: 0
Current S/W+H/W Transmit Queue Length: 1
Broadcast Packets: 1 Broadcast Packets: 0
Multicast Packets: 0 Multicast Packets: 0
No Carrier Sense: 0 CRC Errors: 0
DMA Underrun: 0 DMA Overrun: 0
Lost CTS Errors: 0 Alignment Errors: 0
Max Collision Errors: 0 No Resource Errors: 0
Late Collision Errors: 0 Receive Collision Errors: 0
Deferred: 0 Packet Too Short Errors: 0
SQE Test: 0 Packet Too Long Errors: 0
Timeout Errors: 0 Packets Discarded by Adapter: 0
Single Collision Count: 0 Receiver Start Count: 0
Multiple Collision Count: 0
Current HW Transmit Queue Length: 1
General Statistics:
-------------------
No mbuf Errors: 0
Adapter Reset Count: 0
Adapter Data Rate: 200
Driver Flags: Up Broadcast Running
Simplex AlternateAddress 64BitSupport
PrivateSegment DataRateSet
root@aix# smit tcpip
Minimum Configuration & Startup
To Delete existing configuration data, please use Further Configuration menus
Type or select values in entry fields.
Press Enter AFTER making all desired changes.
[TOP] [Entry Fields]
* HOSTNAME [aix]
* Internet ADDRESS (dotted decimal) [192.168.7.18]
Network MASK (dotted decimal) [255.255.255.0]
* Network INTERFACE en0
NAMESERVER
Internet ADDRESS (dotted decimal) [172.26.160.9]
DOMAIN Name [whatever.com]
Default Gateway
Address (dotted decimal or symbolic name) [192.168.7.1]
Cost [0] #
Do Active Dead Gateway Detection? no
---------- Post updated at 01:00 PM ---------- Previous update was at 12:41 PM ----------
Update: I've made the connection after en1 has been configured.
The next question is how to troubleshoot the en0 issue. How can I find if the interface is broken or not?
Thanks.
Last edited by pludi; 10-26-2009 at 02:17 PM..
Reason: code tags, please...
Hi,
I have broken my laptop hard drive so I would like to put it in an external box to backup my documents.
I have a doubt whether the interface of the hard disk is sata or ide.
Inside notes attached, is reported "controller SATA AHCI" but on the model section is given IDE hard disk
... (1 Reply)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Hi guys,
Is there a command in AIX similar to ps, but shows memory usage by application? I'm trying to track down a rogue application that's using up all 32GB of the available systems memory and causing the the system to page to disk. (4 Replies)
Hi.
I have a Solaris 10 server that's taking about 20secs to respond to telnet or ftp commands. Has anyone ever seen something like that? Can you tell me where to start troubleshooting please? I logged in and did a prtstat, but nothing is jumping out as an issue. (8 Replies)
Hi
I have 2 75GB SCSI hard drives and 2 250GB SATA hard drives which are using RAID Level 1 respectively. I wana have both FTP and Apache installed on them as services. I'm wondering what's the best partitioning schem? I wana use FC3 as my OS, so, I thought I can use the 75GB hard drive as the /... (0 Replies)
