06-27-2014
Thank you a ton
kah00na..... Thats really informative...
Is there any other way to check for SEA ( Shared Ethernet Adapters ) and vlans
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
2. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
3. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
4. AIX
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there... (1 Reply)
Discussion started by: sekarsamy
1 Replies
5. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
6. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
7. AIX
Hi
In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID.
Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies
8. Hardware
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies
9. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
VLAN(4) BSD Kernel Interfaces Manual VLAN(4)
NAME
vlan -- IEEE 802.1Q Virtual LAN network device
SYNOPSIS
pseudo-device vlan
DESCRIPTION
The vlan interface provides support for IEEE 802.1Q Virtual Local Area Networks (VLAN). This supports the trunking of more than one network
on a single network interface. This is particularly useful on routers or on hosts which must be connected to many different networks through
a single physical interface.
To use a vlan interface, the administrator must first create the interface and then specify the VID (VLAN identifier, the first 12 bits from
a 16-bit integer which distinguishes each VLAN from any others) and physical interface associated with the VLAN. This can be done by using
the ifconfig(8) create, vlan, and vlanif subcommands from a shell command line or script. From within a C program, use the ioctl(2) system
call with the SIOCSIFCREATE and SIOCSIFVLAN arguments.
To be compatible with other IEEE 802.1Q devices, the vlan interface supports a 1500 byte MTU, which means that the parent interface will have
to handle packets that are 4 bytes larger than the original Ethernet standard. Drivers supporting this increased MTU are:
- drivers using the DP8390 core (such as ec(4), ne(4), we(4), and possibly others)
- bge(4)
- bnx(4)
- ea(4)
- eb(4)
- epic(4)
- etherip(4)
- ex(4)
- fxp(4)
- gem(4)
- hme(4)
- le(4)
- sip(4)
- ste(4)
- stge(4)
- ti(4)
- tl(4)
- tlp(4)
- vge(4)
- vr(4)
- wm(4)
- xi(4)
vlan can be used with devices not supporting the IEEE 802.1Q MTU, but then the MTU of the vlan interface will be 4 bytes too small and will
not interoperate properly with other IEEE 802.1Q devices, unless the MTU of the other hosts on the VLAN are also lowered to match.
EXAMPLES
The following will create interface vlan0 with VID six, on the Ethernet interface tlp0:
ifconfig vlan0 create
ifconfig vlan0 vlan 6 vlanif tlp0
After this set up, IP addresses (and/or other protocols) can be assigned to the vlan0 interface. All other hosts on the Ethernet connected
to tlp0 which configure a VLAN and use VID six will see all traffic transmitted through vlan0.
The same VLAN can be created at system startup time by placing the following in /etc/ifconfig.vlan0:
create
vlan 6 vlanif tlp0
SEE ALSO
ifconfig(8)
HISTORY
The vlan device first appeared in NetBSD 1.5.1, and was derived from a VLAN implementation that appeared in FreeBSD and OpenBSD.
BUGS
The vlan interfaces do not currently inherit changes made to the physical interfaces' MTU.
BSD
December 16, 2010 BSD