All the nodes in my cluster have the same disk configuration. This is what it looked like about a week before the problem arose:
According to the information at hand, the faulty disk is HDD0 (c2t0d0). This is the one we need to replace. If reseating the drive does not work, and I replace it with another compatible drive, do I have to format or label the spare drive first?
Regards,
Bjoern
Last edited by DukeNuke2; 01-29-2014 at 05:10 PM..
My root disk is failed and how to replace the root disk in AIX.
Can u give a detailed explanation in step wise.
Pls give the answer taking different scenarios.
Regards
Praveen (1 Reply)
Hi All,
I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine.
Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ... (1 Reply)
Hi,
I am trying to write a shell script designed to take input line by line by line from a file with a word on each line for editing with sed. Example file:
1.ejverything
2.bllown
3.maikling
4.manegement
5.existjing
6.systems
My design currently takes input from the user, and... (2 Replies)
Hello,
I wrote a script which monitor the keyswitch state repeatedly each 10 minutes.
I'm extracting the keyswitch status by using prtdiag.
The script works fine for Netra v440 , but I found that prtdiag under Netra 1290 don't give keyswitch status.
unlike Netra 440 server , I found that... (2 Replies)
I got two 2.5" disk for a x4200 and put it in.
Just same these disk were, I remember doing this in the past, working..
Now when I put in the disk and run 'devfsadm' and also check with 'cfgadm -a', that disk doesn't seem to show up.
When I pull out the disk I see this in the logs:
Mar... (15 Replies)
Hello All
I have always had a question about find and replace in Vi. As this uses Vi, sed, and RegEx I never knew how or where to post the question but I thought I would give it a shot here. Say I have a text file filled with the following:
Sue, your IP address is 192.168.1.10 which is... (4 Replies)
Hi all
I wish to mirror for the root disk, but last time i do, make the server cannot boot up. :p So this time, hope you guys can assist me on it. =)
At the last code, is the step i wish to do. Please help to check and correct me if got any wrong.
root@leo # format </dev/null
Searching for... (17 Replies)
Hi All
Hope it's okay to post on this sub-forum, couldn't find a better place
I've got a 480R running solaris 8 with veritas volume manager managing all filesystems, including an encapsulated root disk (I believe the root disk is encapsulated as one of the root mirror disks has an entry under... (1 Reply)
Hello,
I have a spare SUN server X4200 with a DC PSU (oracle part number 300-2186)
The PSU is the one in the photo
I was looking in the net about what cable i can order but i couldn't find anything that fit there :)
Any idea?
Thanks! (2 Replies)
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Discussion started by: CristianS
4 Replies
LEARN ABOUT NETBSD
bioctl
BIOCTL(8) BSD System Manager's Manual BIOCTL(8)NAME
bioctl -- RAID management interface
SYNOPSIS
bioctl device command [arg [...]]
DESCRIPTION
RAID device drivers which support management functionality can register their services with the bio(4) driver. bioctl then can be used to
manage the RAID controller's properties.
COMMANDS
The following commands are supported:
show [disks | volumes]
Without any argument by default bioctl will show information about all volumes and the logical disks used on them. If
disks is specified, only information about physical disks will be shown. If volumes is specified, only information about
the volumes will be shown.
alarm [disable | enable | silence | test]
Control the RAID card's alarm functionality, if supported. By default if no argument is specified, its current state
will be shown. Optionally the disable, enable, silence, or test arguments may be specified to enable, disable, silence,
or test the RAID card's alarm.
blink start channel:target.lun | stop channel:target.lun
Instruct the device at channel:target.lun to start or cease blinking, if there's ses(4) support in the enclosure.
hotspare add channel:target.lun | remove channel:target.lun
Create or remove a hot-spare drive at location channel:target.lun.
passthru add DISKID channel:target.lun | remove channel:target.lun
Create or remove a pass-through device. The DISKID argument specifies the disk that will be used for the new device, and
it will be created at the location channel:target.lun. NOTE: Removing a pass-through device that has a mounted filesys-
tem will lead to undefined behaviour.
check start VOLID | stop VOLID
Start or stop consistency volume check in the volume with index VOLID. NOTE: Not many RAID controllers support this fea-
ture.
create volume VOLID DISKIDs [SIZE] STRIPE RAID_LEVEL channel:target.lun
Create a volume at index VOLID. The DISKIDs argument will specify the first and last disk, i.e.: 0-3 will use the disks
0, 1, 2, and 3. The SIZE argument is optional and may be specified if not all available disk space is wanted (also
dependent of the RAID_LEVEL). The volume will have a stripe size defined in the STRIPE argument and it will be located
at channel:target.lun.
remove volume VOLID channel:target.lun
Remove a volume at index VOLID and located at channel:target.lun. NOTE: Removing a RAID volume that has a mounted
filesystem will lead to undefined behaviour.
EXAMPLES
The following command, executed from the command line, shows the status of the volumes and its logical disks on the RAID controller:
$ bioctl arcmsr0 show
Volume Status Size Device/Label RAID Level Stripe
=================================================================
0 Building 468G sd0 ARC-1210-VOL#00 RAID 6 128KB 0% done
0:0 Online 234G 0:0.0 noencl <WDC WD2500YS-01SHB1 20.06C06>
0:1 Online 234G 0:1.0 noencl <WDC WD2500YS-01SHB1 20.06C06>
0:2 Online 234G 0:2.0 noencl <WDC WD2500YS-01SHB1 20.06C06>
0:3 Online 234G 0:3.0 noencl <WDC WD2500YS-01SHB1 20.06C06>
To create a RAID 5 volume on the SCSI 0:15.0 location on the disks 0, 1, 2, and 3, with stripe size of 64Kb on the first volume ID, using all
available free space on the disks:
$ bioctl arcmsr0 create volume 0 0-3 64 5 0:15.0
To remove the volume 0 previously created at the SCSI 0:15.0 location:
$ bioctl arcmsr0 remove volume 0 0:15.0
SEE ALSO arcmsr(4), bio(4), cac(4), ciss(4), mfi(4)HISTORY
The bioctl command first appeared in OpenBSD 3.8, it was rewritten for NetBSD 5.0.
AUTHORS
The bioctl interface was written by Marco Peereboom <marco@openbsd.org> and was rewritten with multiple features by
Juan Romero Pardines <xtraeme@NetBSD.org>.
BSD March 16, 2008 BSD