The auditors have nailed us for world writeable files....
Apparently in years gone by, quite a number of our kornshell scripts have had:
umask 000 put in the script.
We have been able to turn off world writeable for existing dirs & files, but as these scripts run, new files keep getting... (1 Reply)
Hi All,
i have a file file.dat with following data :
CONTENT_STORAGE PERCENTAGE FLAG:
storage_02 64% 0
storage_01 17% 1
i need to update FLAG field of storage_02 to 1
i am using the following: but its not working :
awk '{FS=OFS=" "}$1==$defaultStorage1{$3="1"}1'... (13 Replies)
I have a file contains 100 section (here i show 2 section of that); i want to replace date from 1st & 2nd field of 1st line of each section (1st line of each section is header and the other lines are body) and merg them into one field, then copy it on 7th field of the lines in each section... (17 Replies)
Hi
I have a job status csv file. I want to update the status of the job in the file.
Below is the csv file
1,jobname1,in_progress,starttime,somthing,somthing
2,jobname2,completed,starttime,somthing,somthing
3,jobname3,failed,starttime,somthing,somthing... (8 Replies)
I am trying to add 0393 value at 24th feild using the below command, but its adding at all the lines including header and trailer
Input file:
ZHV|2657|D0217001|T|TXU|Z|PAN|20131112000552||||OPER|
754|52479|
492|489|SP40|1014570286334|20131111|20131201|14355334|CHAMELON... (1 Reply)
Look at this simple example.
echo " 2 4 6" | awk '{$2+=3;$3-=1}1'
2 7 5
Is there a simple way to update a field and at the same time keep the formatting?
I would like to get it like this
2 7 5
I have tested both sub and gsub, it reformat too. (2 Replies)
In the tab-delimeted input file below I am trying to use awk to update the value in $2 if TYPE=ins in bold, by adding the value of
HRUN= in italics. In the below since in line 1 TYPE=ins the 117282541 value in $2 has 6 added because that is the value of HRUN=.
Hopefully the awk is a start but I... (2 Replies)
Trying to use awk to:
update $2 in file2 with the $2 value in file1, if $1 in file1 matches $13 in file2, which is tab-delimeted. The $2values may already be the same so in that case nothing happens and the next line is processed.
There are exactly 4,605 unique $13 values. Thank you :).
... (4 Replies)
In the out.txt below I am trying to use awk to update the contents of $9.. If $9 contains a + or - then $8 of out.txt is used as a key to lookup in $2 of file. When a match ( there will always be one) is found the $3 value of that file is used to update $9 of out.txt separated by a :. So the... (6 Replies)
In the awk below I am trying to set/update the value of $14 in file2 in
bold, using the matching NM_ in $12 or $9 in file2
with the NM_ in $2 of file1.
The lengths of $9 and $12 can be variable but what is consistent is the start pattern
will always be NM_ and the end pattern is always ;... (2 Replies)
Discussion started by: cmccabe
2 Replies
LEARN ABOUT DEBIAN
grdcut
GRDCUT(l) GRDCUT(l)
NAME
grdcut - Extract a subregion out of a .grd file
SYNOPSIS
grdcut input_file.grd -Goutput_file.grd -Rwest/east/south/north[r] [ -V ]
DESCRIPTION
grdcut will produce a new output_file.grd file which is a subregion of input_file.grd. The subregion is specified with
-Rwest/east/south/north as in other programs; the specified range must not exceed the range of input_file.grd. If in doubt, run grdinfo to
check range. Complementary to grdcut there is grdpaste, which will join together two grdfiles along a common edge.
input_file.grd
this is the input .grd format file.
-Goutput_file.grd
this is the output .grd format file.
-R west, east, south, and north specify the Region of interest. To specify boundaries in degrees and minutes [and seconds], use the
dd:mm[:ss] format. Append r if lower left and upper right map coordinates are given instead of wesn. This defines the subregion to
be cut out.
OPTIONS -V Selects verbose mode, which will send progress reports to stderr [Default runs "silently"].
EXAMPLES
Suppose you have used surface to grid ship gravity in the region between 148E - 162E and 8N - 32N, and you do not trust the gridding near
the edges, so you want to keep only the area between 150E - 160E and 10N - 30N, then:
grdcut grav_148_162_8_32.grd -Ggrav_150_160_10_30.grd -R150/160/10/30 -V
SEE ALSO grdpaste(1gmt), grdinfo(1gmt), gmt(1gmt)
1 Jan 2004 GRDCUT(l)