PowerHA HACMP on VIOS servers Post: 302774883

10 More Discussions You Might Find Interesting

1. AIX

Duplicate IP address makes PowerHA ( HACMP ) down

Hello, I would like to know if anyone has faced this problem. Whenever there is a duplicate IP address, HACMP goes down infact HACMP ( PowerHA ) takes the whole system down. Does anyone know how to solve this problem ?

2. AIX

HACMP does not start db2 after failover (db2nodes not getting modified by hacmp)

hi, when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is...

3. AIX

Interoperability Oracle Clusterware - PowerHA/HACMP

I am planning for building a new database server using AIX 6.1 and Oracle 11.2 using ASM. As i have learned starting with Oracle 11.2 ASM can only be used in conjunction with Clusterware, which is Oracles HA-software. As is the companies policy we do intend to use PowerHA as HA-solution instead...

4. AIX

Increase LUN size in AIX with VIOS and HACMP

Hello! I have this infraestructure: - 1 POWER7 with single VIOS on Site A. - 1 POWER6 with single VIOS on Site B. - 1 LPAR called NodeA as primary node for PowerHA 6.1 on Site A. - 1 LPAR called NodeB as secondary (cold) node for PowerHA 6.1 on SiteB. - 1 Storage DS4700 on Site A. - 1...

5. AIX

PowerHA Disk on VIO Server

Hello AIX GURU's Can anybody tell me the steps to crate shared VG (enhanced concurent) for my Lpars from VIO server? my questions are: 1. Should I crate Enhanced Concurent VG in VIO and map it using virtual Scsi to Lpar? or 2. Can I just create virtual SCSI in VIO and map to Lpar and...

6. AIX

VIOS IP address - separate vlan for vios servers ?

Hello, Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2. What is the common practice - should I isolate my vios...

7. AIX

PowerHA(HACMP) full vg loss - cluster hangs on release_vg_fs event

Hello, AIX 6.1 TL7 SP6 POwerHA 6.1 SP10 I was experimenting with new hacmp build. It's 3-node cluster build on AIX 6.1 lpars. It contains Ethernet and diskhb networks. Shared vg disk is SAN disk. Two nodes see disk using vscsi, third node sees disk using npiv. Application is db2 server. ...

8. AIX

Powerha on AIX 6.1.9

hello ive installed powerha 7.1.3 on two servers aix 6.1.9 6100-09-03-1415 work with dmx4 EMC storgae. after sync cluster ( terminate with OK ) ive see that the repository disk upper only in one machine : hdiskpower60 00c7f6b59fc60d9d caavg_private active...

9. AIX

VXVM in POWERHA 6.1

I have created a VxVM disk group in AIX7.1. I have tried to added this VxVM disk group in powerHA 6.1. But in cluster VxVM DGs are not listing. Is there any other procedure to add vxvm diskgroup to hacmp. Please share me steps for adding vxvm diskgroup to hacmp.

10. AIX

Upgrading PowerHA from 7.1.0 to 7.1.3

Hi All, As per the IBM upgrade/support matrix IBM Techdocs Technote: PowerHA for AIX Version Compatibility Matrix we can't do online upgrade or rolling migration from powerha v7.1.0 to v7.1.3. on AIX61_TL9_SP4, So we are following the steps as below ... 1 ) Bring down the cluster 2 )...

LEARN ABOUT NETBSD

urlphy

URL(4)							   BSD Kernel Interfaces Manual 						    URL(4)

NAME

     url -- Realtek RTL8150L USB Ethernet driver

SYNOPSIS

     url*    at uhub?
     urlphy* at mii?

DESCRIPTION

     The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.

     The url driver supports the following adapters:

	   CompUSA USBKR100
	   GreenHouse GH-USB100B
	   Melco Inc. LUA-KTX
	   Sitecom LN013

     For more information on configuring this device, see ifconfig(8).

DIAGNOSTICS

     url%d: watchdog timeout  A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
     transmission before a timeout expired.

     url%d: no memory for rx list  The driver failed to allocate an mbuf for the receiver ring.

SEE ALSO

     arp(4), mii(4), netintro(4), usb(4), ifconfig(8)

HISTORY

     The url device driver first appeared in NetBSD 1.6.

AUTHORS

     The url driver was written by Shingo WATANABE <nabe@nabechan.org>.

BSD
								September 18, 2006							       BSD