01-02-2013
Solution | Resolved LPAR VIOS IVM POWERVM AIX CD-ROM
When I restarted the LPAR after assigning it, from SMS menu I was able to detect it.
Apparently as Michael Felt said, the issue is with the AIX 5.3 ML 00 !!
With AIX 6.1 , I can assign the CD - ROM through web and it will be detected after executing cfgmgr !
10 More Discussions You Might Find Interesting
1. AIX
When using PowerVM Express and IVM (no HMC) on a Power6 P520 , can I configure 2 LPARs in addition to a VIO server, or does the VIO Server count as one of the two LPAR's that PowerVM Express allows? (1 Reply)
Discussion started by: JodyTek
1 Replies
2. HP-UX
Please help me >
How to diag the external DVD-ROM drive issue whether it is working or not? on HP 9000 server rp7400
I needed to install HP 11i v1 using external DVD-ROM drive on HP 9000 server rp7400. While boot in CO> “search” command is not showing DVD-ROM device only showing all disks >... (0 Replies)
Discussion started by: tpuser
0 Replies
3. UNIX for Advanced & Expert Users
old clunker - rp74000
How to diag the external DVD-ROM drives issue whether it is working or not? on HP 9000 server rp7400
Please help me > I needed to install HP 11i v1 using external DVD-ROM drive on HP 9000 server rp7400. While boot in CO> “search” command is not showing DVD-ROM device... (1 Reply)
Discussion started by: tpuser
1 Replies
4. AIX
Hi everyone,
Sorry if this post is in the wrong place. I searched the forums for "IVM" and it turned up no results. Hopefully someone knows about this. My dilemma is that I have multiple IBM JS12 Express blades in our blade center, each running VIOS 2.1.0.10-FP-20.1 and hosting a couple LPARs. Out... (2 Replies)
Discussion started by: need2bageek
2 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. AIX
Hi,
When I try to login on my vios ivm website http://vios through the browser -- all three of them -- firefox , chrome , Internet Explorer , i get this error
http://vioserver/j_security_check
I have java installed on the machine from where i am trying to open up the IVM/VIOS webpage.
I... (2 Replies)
Discussion started by: filosophizer
2 Replies
7. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
8. AIX
Hi All,
I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM
Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box.
We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
Discussion started by: KevB
11 Replies
9. AIX
coming from this thread: https://www.unix.com/aix/211107-ibm-power-pseries-open-firmware-boot-vios-powervm-vet-code.html
PowerVM, formerly known as Advanced Power Virtualization (APV), is a chargeable feature of IBM POWER5, POWER6, POWER7, POWER8, and POWER9 servers and is required for support... (0 Replies)
Discussion started by: filosophizer
0 Replies
10. AIX
Hello,
After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 )
i get this message
"I/O hosting requires a hosting partition - boot not permitted".
HMC was connected to the machine
then HMC was removed through ASMI
Searching on... (2 Replies)
Discussion started by: filosophizer
2 Replies
LEARN ABOUT OSF1
sys_attrs_tc
sys_attrs_tc(5) File Formats Manual sys_attrs_tc(5)
NAME
sys_attrs_tc - tc subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the TURBOchannel Bus (tc) kernel subsystem. Refer to the sys_attrs(5) reference page
for an introduction to the topic of kernel subsystem attributes.
For this subsytem, users should modify only the following attribute and do so only for the purpose described. Any other visible attributes
cannot or should not be modified.
Enables (nonzero value) or disables (0) console messages that appear at boot time and runtime for use by device driver developers to
collect information about a driver configuration problem. A developer can set this attribute by using the sysconfig or sysconfigdb
utility. See sysconfig(8), sysconfigdb(8), and cfgmgr(8) for more information on options for modifying attributes and reconfiguring
a kernel subsystem.
Default value: 0 (disabled)
SEE ALSO
Commands: cfgmgr(8), sysconfig(8), sysconfigdb(8)
Files: stanza(4), cfgmgr.auth(4), sysconfigtab(4)
Others: sys_attrs(5)
Writing TURBOchannel Device Drivers
sys_attrs_tc(5)