Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Dears,
i follow this to configure Network interface for my PC
O/S : Unix Sun Solaris
vi /etc/hostname.bge0
and write my ip
vi /etc/netmasks
and write my subnetmask
vi /etc/defautrouter
and write my gatwey
vi /etc/resolv.conf
and write my DNS
after i reboot My Computer ... (3 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Hello,
Is there any API or any other approach to detect whether the network cable is connected to the network adapter, say, en0, en1 or en2?
The OS is AIX6.1.
Thank you. (4 Replies)
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT FREEBSD
halt
REBOOT(8) BSD System Manager's Manual REBOOT(8)NAME
reboot, halt, fastboot, fasthalt -- stopping and restarting the system
SYNOPSIS
halt [-lnpq] [-k kernel]
reboot [-dlnpq] [-k kernel]
fasthalt [-lnpq] [-k kernel]
fastboot [-dlnpq] [-k kernel]
DESCRIPTION
The halt and reboot utilities flush the file system cache to disk, send all running processes a SIGTERM (and subsequently a SIGKILL) and,
respectively, halt or restart the system. The action is logged, including entering a shutdown record into the user accounting database.
The options are as follows:
-d The system is requested to create a crash dump. This option is supported only when rebooting, and it has no effect unless a dump
device has previously been specified with dumpon(8).
-k kernel
Boot the specified kernel on the next system boot. If the kernel boots successfully, the default kernel will be booted on successive
boots, this is a one-shot option. If the boot fails, the system will continue attempting to boot kernel until the boot process is
interrupted and a valid kernel booted. This may change in the future.
-l The halt or reboot is not logged to the system log. This option is intended for applications such as shutdown(8), that call reboot
or halt and log this themselves.
-n The file system cache is not flushed. This option should probably not be used.
-p The system will turn off the power if it can. If the power down action fails, the system will halt or reboot normally, depending on
whether halt or reboot was called.
-q The system is halted or restarted quickly and ungracefully, and only the flushing of the file system cache is performed (if the -n
option is not specified). This option should probably not be used.
The fasthalt and fastboot utilities are nothing more than aliases for the halt and reboot utilities.
Normally, the shutdown(8) utility is used when the system needs to be halted or restarted, giving users advance warning of their impending
doom and cleanly terminating specific programs.
SEE ALSO getutxent(3), boot(8), dumpon(8), nextboot(8), savecore(8), shutdown(8), sync(8)HISTORY
A reboot utility appeared in Version 6 AT&T UNIX.
BSD October 11, 2010 BSD