Sponsored Content
Full Discussion: HACMP
Operating Systems AIX HACMP Post 302676311 by zaxxon on Tuesday 24th of July 2012 11:50:33 AM
Old 07-24-2012
At the IBM Info Center there are some related articles about problems with DMS being triggered while everything is node-wise ok:
Help - AIX 6.1 Information Center: HACMP takeover issues

Check out especially:
Releasing large amounts of TCP traffic causes DMS timeout
Deadman switch causes a node failure
Deadman switch time to trigger
 

10 More Discussions You Might Find Interesting

1. AIX

Hacmp

(0 Replies)
Discussion started by: mhenryj
0 Replies

2. AIX

HACMP (Again)

Hello I am a noobie to HACMP I have 2 55A servers and a 7031 disk subsystem For HACMP to work, do I need to have the hdisks on both servers to match the same drives?? The hdisks on each box are currently different: hdisk0 and hdisk1 are the internal disks and hdisk2-5 are on the D24 on... (1 Reply)
Discussion started by: mhenryj
1 Replies

3. HP-UX

HACMP in HP-UX

Hi, Can anybody advice whether it is possible to configure HACMP in HP-UX Server. To my knowledge HACMP is IBM Solution. Thanks && Regards, N. Poorna Chandra Rao. (2 Replies)
Discussion started by: npcrao
2 Replies

4. AIX

Did a Mistake with HACMP

Hi, I needed space on a FS, and when I've added the space on the filesystem, I did it trough the regular smitty fs inteface and not with smitty cl_lvm. Can someone help me to repair the situat before a faileover happen ? Thanks for your help,:mad: (13 Replies)
Discussion started by: azzed27
13 Replies

5. AIX

HACMP

Hi, Can we use network for heartbeat, I mean can we use different network card for heartbeat. (6 Replies)
Discussion started by: vjm
6 Replies

6. AIX

HACMP

hi can anyone explain the concepts of HACMP and configuration (step by step) (2 Replies)
Discussion started by: udtyuvaraj
2 Replies

7. AIX

HACMP does not start db2 after failover (db2nodes not getting modified by hacmp)

hi, when I do a failover, hacmp always starts db2 but recently it fails to start db2..noticed the issue is db2nodes.cfg is not modified by hacmp and is still showing primary node..manually changed the node name to secondary after which db2 started immediately..unable to figure out why hacmp is... (4 Replies)
Discussion started by: gkr747
4 Replies

8. AIX

Help with HACMP

Hi. We have a two node HA cluster. We got a request to change one of the VG name? Is there an option to do this online ? If it requires downtime can someone please explain me the steps for doing it ? Let me know if you need any outputs from the servers (1 Reply)
Discussion started by: newtoaixos
1 Replies

9. AIX

Hacmp

Hi, I have question about HA. I have 2 node cluster (node A and node B). I have configured network and disk HB. If my network is up and i remove both the fc cables from node A will my cluster failover to node B? I have checked and its not working, if i want my cluster to failover in this... (5 Replies)
Discussion started by: powerAIX
5 Replies

10. AIX

Hacmp

hello ive 2 nodes aix 6100-04-10-1119 with hacmp 6.1.0.0 my qustion is : can i add default gateway to one member node with hacmp a live or to do take over to realse one of the members ? thanks When it is urgent, then open the thread up in the appropriate subforum next time, thanks. (3 Replies)
Discussion started by: ariec
3 Replies
URL(4)							   BSD Kernel Interfaces Manual 						    URL(4)

NAME
url -- Realtek RTL8150L USB Ethernet driver SYNOPSIS
url* at uhub? urlphy* at mii? DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip. The url driver supports the following adapters: CompUSA USBKR100 GreenHouse GH-USB100B Melco Inc. LUA-KTX Sitecom LN013 For more information on configuring this device, see ifconfig(8). DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8) HISTORY
The url device driver first appeared in NetBSD 1.6. AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>. BSD
September 18, 2006 BSD
All times are GMT -4. The time now is 08:34 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy