Sponsored Content
Full Discussion: Enable ftp port
Operating Systems HP-UX Enable ftp port Post 302629701 by sai_2507 on Wednesday 25th of April 2012 04:16:23 AM
Old 04-25-2012
Hi Vbe

Thanks for the reply

No it is not not commented as shown in below code.

Code:
 
$ more /etc/inetd.conf |grep ftp
ftp          stream tcp nowait root /usr/lbin/ftpd      ftpd -l -a -u 002
# Before uncommenting the "tftp" entry below, please make sure
# that you have a "tftp" user in /etc/passwd. If you don't
# have one, please consult the tftpd(1M) manual entry for
$

 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Enable FTP on SCO

My goal is to use FTP to transfer file between PC and SCO Unix server.When I try to connect via FTP with root user, it failed. What should I do? How to configure ftpaccess? Thanks in advance! (2 Replies)
Discussion started by: Vladan
2 Replies

2. Linux

ftp telnet enable

hi , i have jsut installed linux 9.0 , but i can not ftp or telnet to the system . i have installed the ftp and the telnet server during installation . i have also configured the files to enable the ftp and telnet , the ftp and the telnet daemons are running , but when i do ftp : ftp... (1 Reply)
Discussion started by: ppass
1 Replies

3. Solaris

Solaris 8 - FTP server -enable

Hi, I have turn off the FTP service and rebooted the server . (edit /etc/inetd.conf and /etc/inet/services) Now , how can I enable back the FTP without rebooting the server . Thanks (1 Reply)
Discussion started by: civic2005
1 Replies

4. Red Hat

enable FTP access / check version

how can I check the Linux version? (14 Replies)
Discussion started by: zp523444
14 Replies

5. UNIX for Dummies Questions & Answers

USB port is disabled using BIOS, I want to enable it

Hi, I have PC with Linux OS RHEL3 and USB port is disabled from BIOS. BIOS access is protected using password. But, I have root access. Now, how can I enable USB port using root access? Is there any trick that I can do using root access that can enable USB port once my PC has booted up? (3 Replies)
Discussion started by: gydave
3 Replies

6. Solaris

How to enable hba port of a two port hba card

Hi, i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port. ---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ---------- please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies

7. Solaris

Enable FTP for root user in Solaris 10

I am not able to get ftp working for Solaris 10 for root user. I am getting login failed error. 331 Password required for root. Password: 530 Login incorrect. Login failed. Tried following things already. 1. SFTP works ok, still would like to know why FTP is not working (curious). 2.... (5 Replies)
Discussion started by: webkid
5 Replies

8. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies

9. HP-UX

FTP service Enable/Disable

hi everybody, I can easily enable /disable the FTP service from SAM, how can I do this via command line? using inetd? how? cheers, messi (1 Reply)
Discussion started by: messi777
1 Replies

10. Shell Programming and Scripting

Enable Annonymous FTP login.

Hi, I am transferring my report files to another FTP server which the end users are downloading later. But while accessing the FTP server its asking for username and password which i don't want to share to the end users rather i want to make the login as anonymous so that it... (3 Replies)
Discussion started by: Showdown
3 Replies
bup-ftp(1)						      General Commands Manual							bup-ftp(1)

NAME
bup-web - Start web server to browse bup repositiory SYNOPSIS
bup web [[hostname]:port] DESCRIPTION
bup web starts a web server that can browse bup repositories. The file hierarchy is the same as that shown by bup-fuse(1), bup-ls(1) and bup-ftp(1). hostname and port default to 127.0.0.1 and 8080, respectively, and hence bup web will only offer up the web server to locally running clients. If you'd like to expose the web server to anyone on your network (dangerous!) you can omit the bind address to bind to all avail- able interfaces: :8080. EXAMPLE
$ bup web Serving HTTP on 127.0.0.1:8080... ^C $ bup web :8080 Serving HTTP on 0.0.0.0:8080... ^C SEE ALSO
bup-fuse(1), bup-ls(1), bup-ftp(1), bup-restore(1) BUP
Part of the bup(1) suite. AUTHORS
Joe Beda <jbeda@gmail.com>. Bup unknown- bup-ftp(1)
All times are GMT -4. The time now is 07:57 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy