Hi all,
i must do a little script that send AT command at ttyUSB3..
for example:
Start Minicom:
Set serial port ttyUSB3
AT+CREG?
if response != OK then do something
...other AT command (open a socket tcp/ip with at comman)
Send a file .txt for example.
exit minicom.
I saw on the network command "expect" but I have not undarstand how to launch minicom and give it commands to set the right port ..
thanks for help
I don't have a modem now (left it in Antarctica believe it or not), so it is hard to test/script this for you, but Corona is certainly right that you would not use minicom.
PPPD comes with 'chat' which is a good way to do the initial parts of opening connection. I would use that. Again, untested:
Last edited by neutronscott; 04-19-2012 at 10:10 AM..
Reason: save stdout fd
hello. i'm attempting to use minicom in linux, but i'm having some difficulties. When i type in "minicom", the application opens up. It says 'starting minicom/finding modem'(something like that). However, once it actually starts, I can't do anything. No matter what I type in, it doesn't work. ... (2 Replies)
Does anyone have a working minicom script they would care to post as I can't get the scripting working and the scriptdemo and unixlogin sample scripts are on my system either.
Thanx,
I (2 Replies)
Hi,
I am new to use minicom. I want script to run on minicom with username and password as automated.(Expect). please could anyone suggest the sample code for it.
Thanks in advance (2 Replies)
Hi,
I am new to using minicom. I want how to write a expect script for minicom login? I wrote a code but its not acting what iam expecting. here I have my code:
#!/usr/bin/expect
set fd
fconfigure $fd
spawn -open $fd
spawn minicom
expect “enter:”
send "\n"
send "\n"
... (3 Replies)
Hi all,
I have some trouble getting stty to talk to some serial/usb converter.
Getting minicom to work was however quite simple after I entered the following settings in addition to its standard-setup:
pu port /dev/ttyUSB0
pu baudrate 19200
pu bits 8
pu... (3 Replies)
This is what I've tried:
#!/bin/sh
send sh
send showifs
send exit
! killall minicom
My problem is that for some reason when I do this it doesn't give me the results of the prior commands sent like showifs
So I suspect my syntax is wrong. (1 Reply)
I'm a fairly new user to Linux based systems and am still a little uncomfortable with using the command interface. I'm trying to get my feet wet but have unfortunately hit a wall and am actually not even sure what I am trying to accomplish is at all possible.
Basically, I am trying to use a... (0 Replies)
Hi All,
I am testing expect script in command prompt without issue, but in crontab it is not working, i check the output error as below:
#cat /var/log/testexp.log
spawn minicom -C /var/log/minicom1.log
No cursor motion capability (cm)
AT+COPS=?
I am new in scripting, together... (1 Reply)
Hey All,
I am trying to find something similar to minicom, but it needs the ability to be ran during a remote dialup session on the remote
device's side.
If I dial into the remote server (*using minicom) and then try to run minicom on the remote server I get the following:
# minicom... (20 Replies)
Discussion started by: mrm5102
20 Replies
LEARN ABOUT LINUX
service
service(8) System Manager's Manual service(8)NAME
service - run a System V init script
SYNOPSIS
service SCRIPT COMMAND [OPTIONS]
service --status-all
service --help | -h | --version
DESCRIPTION
service runs a System V init script in as predictable environment as possible, removing most environment variables and with current working
directory set to /.
The SCRIPT parameter specifies a System V init script, located in /etc/init.d/SCRIPT. The supported values of COMMAND depend on the
invoked script, service passes COMMAND and OPTIONS it to the init script unmodified. All scripts should support at least the start and
stop commands. As a special case, if COMMAND is --full-restart, the script is run twice, first with the stop command, then with the start
command.
service --status-all runs all init scripts, in alphabetical order, with the status command.
EXIT CODES
service calls the init script and returns the status returned by it.
FILES
/etc/init.d
The directory containing System V init scripts.
ENVIRONMENT
LANG, TERM
The only environment variables passed to the init scripts.
SEE ALSO
/etc/init.d/skeleton,
update-rc.d(8),
init(8),
invoke-rc.d(8).
Jan 2006 service(8)